Mitsubishi Electronics EW330U Adjusting the projected image, Adjusting the projection angle

Page 25

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

1. Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2. Screw the rear adjuster foot to fine tune the horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are	2	1
not perpendicular to each other, the projected image becomes trapezoidal. To

correct this situation, see "Correcting keystone" on page 26 for details.

• Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

•Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3 seconds.

• The screen will be blank while AUTO is functioning.

•This function is only available when a PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

In the right figure, (A) Focus Ring, (B) Zoom Ring
1.	Adjust Zoom. (using (B) Zoom Ring)		A
2.	For the short distance/large screen, dial the ring fully to Wide end.	Tele	Wide
3.	For the long distance/small screen, dial the ring fully to Tele end.		B
3.	Adjust Focus. (using (A) Focus Ring)
4.	Move the product back and forth to adjust the screen size.
5.	Adjust Focus again if necessary.

ENGLISH

EN-25

Image 25

Contents EX320U/EW330U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Kensington Lock Projector exterior viewFront/upper side Projector Controls and functionsMagnifying and searching for details on page 26 for Remote controlUsing the remote control for the first time Choosing a location Positioning your projectorObtaining a preferred projected image size When fine streaks are seen on projected imagesEN-13 Front projection Layout of the projectorStandard 261 664 147 374 314 408 10.4 169Connecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerConnecting a monitor Connecting Video source devicesTo connect the projector to a monitor Connecting a Component Video source device Connecting an Hdmi deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUsing the menus Setting a password Utilizing the password functionIf you forget the password Entering the password recall procedureDisabling the password function Switching input signalChanging Color Space Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsEW330U EX320U Selecting the aspect ratioEN-28 Picture modes for different types of signals Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageFine-tuning the image quality in user modes 3D Color Management Using Wall ScreenImmediately To cancel the timer, perform the following steps Setting the presentation timerHow to use the Timer On key? Hiding the image Adjusting the soundLocking control keys Freezing the imagePersonalizing the projector menu display Direct power offShutting down the projector Standby Audio OutL R Watching 3D ContentMode Resolution H x Horizontal Frequency Vertical Frequency Supervising and controlling by computer Configuring the LAN Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environmentPress / to reveal About PJLink Controlling the projector using PJLink applicationPJLinksupported commands Utilizing the password functionGlossary How to Use Network FunctionMenu system Menu operationSystem Setup Blank Timer Description Description of each menuSetting Brightness Contrast Color Reset lamp timer Lamp modeMenu display time Menu positionPower on lock Change passwordClosed Caption Enable SettingCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as LowLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampSpare lamp for EX320U/EW330U VLT-EX320LP Replacing the lampResetting the lamp timer EN-53 Down without the normal cooling down process IndicatorsProjector needs 90 seconds to cool down Please contact your dealer for assistanceTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation