Mitsubishi Electronics EW330U, EX320U user manual How to Use Network Function, Glossary

Page 41

 

 

 

 

 

INF2?

Inquiry about the model name

"EX320U" or "EW330U" is returned.

ENGLISH

 

 

 

INF0?

Inquiry about other information

No other information is available. No parameter is returned.

 

 

 

 

 

 

 

CLSS?

Inquiry about the class information

"1" is returned.

 

 

 

 

 

 

 

The PJLink "INPT?" will be replied only when the source is displayed on screen. When there is no signal, only "Unavailable Time!" will be answered.

The above-mentioned control may not be performed correctly or the monitoring data may not be obtained correctly in the following conditions:

During standby

During input source switching

During command processing

During AUTO execution

Before the splash screen disappears after the power is turned on.

Use 1 computer to control/monitor 1 projector.

For how to control/monitor using PJLink™, see the operation manual of the PJLink™ application you use.

When you monitor the projector's operating state using this function by issuing inquiry commands successively, issue an inquiry command after receiving the response to the previous inquiry command from the projector.

How to Use Network Function

When connecting a computer and projector with LAN, configure the both IP Addresses in the same network group.

Configure the IP CONFIG correctly. If the settings are not correct, the communication may be unavailable. For the detail, consult the network administrator.

When the Control By in the SYSTEM SETUP: Advanced > LAN Control Settings menu is selected RS-232C, the LAN Control Settings function is not available.

Glossary

For more detail of the glossary below, refer to the technical book that is commercially available.

Term

Description

DHCP

Abbreviation for Dynamic Host Confi guration Protocol. This protocol

 

automatically assigns IP Address to networked devices.

IP Address

Numerical address to identify networked computers.

Subnet Mask

A numeric value to defi ne the number of bits used for a network

 

address of a divided network (or subnet) in an IP Address.

Default Gateway

A server (or router) to communicate across networks (subnets) that

 

are divided by Subnet Mask.

 

 

MAC Address

Abbreviation for Media Access Control Address. MAC Address is a

 

unique ID number assigned to each network adapter. And this is

 

based on which data are sent and received between network adapt-

 

ers.

EN-41

Image 41
Contents EX320U/EW330U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Front/upper side Projector exterior viewKensington Lock Projector Controls and functionsMagnifying and searching for details on page 26 for Remote controlUsing the remote control for the first time Choosing a location Positioning your projectorObtaining a preferred projected image size When fine streaks are seen on projected imagesEN-13 Standard Layout of the projectorFront projection 261 664 147 374 314 408 10.4 169Connecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting Video source devicesConnecting a monitor Connecting a Component Video source device Connecting an Hdmi deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUsing the menus Setting a password Utilizing the password functionIf you forget the password Entering the password recall procedureChanging Color Space Switching input signalDisabling the password function Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsEW330U EX320U Selecting the aspect ratioEN-28 Picture modes for different types of signals Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageFine-tuning the image quality in user modes Immediately Using Wall Screen3D Color Management How to use the Timer On key? Setting the presentation timerTo cancel the timer, perform the following steps Hiding the image Adjusting the soundLocking control keys Freezing the imagePersonalizing the projector menu display Direct power offShutting down the projector Standby Audio OutL R Watching 3D ContentMode Resolution H x Horizontal Frequency Vertical Frequency Supervising and controlling by computer Configuring the LAN Control SettingsIf you are in a Dhcp environment If you are in a non-DHCP environmentPress / to reveal About PJLink Controlling the projector using PJLink applicationPJLinksupported commands Utilizing the password functionGlossary How to Use Network FunctionMenu system Menu operationSystem Setup Blank Timer Description Description of each menuSetting Brightness Contrast Color Reset lamp timer Lamp modeMenu display time Menu positionPower on lock Change passwordClosed Caption Enable SettingCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as LowLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampSpare lamp for EX320U/EW330U VLT-EX320LP Replacing the lampResetting the lamp timer EN-53 Down without the normal cooling down process IndicatorsProjector needs 90 seconds to cool down Please contact your dealer for assistanceTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation