Mitsubishi Electronics user manual Replacing the lamp, Spare lamp for EX320U/EW330U VLT-EX320LP

Page 51

Replacing the lamp

 

Spare lamp for EX320U/EW330U: VLT-EX320LP

• Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp.

To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces. To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.

Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation may also result in fire.

If the lamp should break, never shake the lamp box or hold it in front of your face after removing it. The glass fragments may fall out and cause injury to your eyes.

In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace the lamp by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments.

Contact your dealer when replacing the lamp unit with the projector mounted to the ceiling.

Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a breakdown.

This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may explode or fail to illuminate permanently because of an impact, scratch, or deterioration through use. The period of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on operation conditions. Therefore, the lamp may explode soon after the start of use.

The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction of lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting normally.

When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and the gas charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains mercury. Be careful not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see a doctor immediately.

This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.

Be sure to use the lamp dedicated to this projector, VLT-EX320LP for EX320U/EW330U. Use of other lamps may cause a failure of the projector.

ENGLISH

1.Turn the power off and disconnect the projector from the wall socket. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2.Unscrew the screws on the lamp cover.

3.Remove the lamp cover from the projector.

1, 2

Pull up the lamp cover, pussing up the allow parts of the front panel.

• Do not turn the power on with the lamp cover removed.

Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

2

 

2

 

 

 

1

3

 

 

4.Remove and dispose of the lamp protection film. 3

5.Loosen the screw that secures the lamp.

1

2

EN-51

Image 51
Contents EX320U/EW330U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Projector exterior view Kensington LockFront/upper side Projector Controls and functionsMagnifying and searching for details on page 26 for Remote controlUsing the remote control for the first time Choosing a location Positioning your projectorObtaining a preferred projected image size When fine streaks are seen on projected imagesEN-13 Layout of the projector Front projectionStandard 261 664 147 374 314 408 10.4 169To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionConnecting Video source devices Connecting a monitorTo connect the projector to a monitor To connect the projector to a Component Video source device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to an Hdmi deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUsing the menus Entering the password recall procedure Utilizing the password functionSetting a password If you forget the passwordSwitching input signal Disabling the password functionChanging Color Space Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsEW330U EX320U Selecting the aspect ratioEN-28 Optimizing the image Selecting a picture modePicture modes for different types of signals Setting the User 1/User 2 modeFine-tuning the image quality in user modes Using Wall Screen 3D Color ManagementImmediately Setting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Adjusting the soundHiding the image Locking control keysStandby Audio Out Direct power offPersonalizing the projector menu display Shutting down the projectorL R Watching 3D ContentMode Resolution H x Horizontal Frequency Vertical Frequency If you are in a non-DHCP environment Configuring the LAN Control SettingsSupervising and controlling by computer If you are in a Dhcp environmentPress / to reveal About PJLink Controlling the projector using PJLink applicationPJLinksupported commands Utilizing the password functionGlossary How to Use Network FunctionMenu system Menu operationSystem Setup Blank Timer Description Description of each menuSetting Brightness Contrast Color Menu position Lamp modeReset lamp timer Menu display timeSetting Change passwordPower on lock Closed Caption EnableCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as LowSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampSpare lamp for EX320U/EW330U VLT-EX320LP Replacing the lampResetting the lamp timer EN-53 Please contact your dealer for assistance IndicatorsDown without the normal cooling down process Projector needs 90 seconds to cool downTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation