Onkyo HT-R410 Positioning speakers/Connecting speakers, How to connect to the speaker terminals

Page 13

Positioning speakers/Connecting speakers

Before connecting

Refer also to the instruction manuals of the speakers.

Be sure to connect the positive and negative cables for the speakers properly. If they are mixed up, the left and right signals will be reversed and the audio will sound unnatural.

Connect speakers with an impedance between 8 and 16 Connecting speakers with an impedance less than 8 may damage the HT-R410.

To prevent damage to circuits, never short-circuit the positive

(+) and negative (–) speaker wires.

NO!

Do not connect more than one speaker cable to one speaker terminal. Doing so may damage the HT-R410.

When you are using only one speaker or when you wish to listen to monaural (mono) sound, a single speaker should never be connected in parallel to both the right and left channel terminals simultaneously.

How to connect to the speaker terminals

3/8” (10 mm)

Strip 3/8” (10 mm)

Press and hold

Insert the stripped

end of the cable.

from the end of

the lever.

By releasing the

each cable, then

 

twist the exposed

 

lever, the lever is

wires tightly.

 

replaced.

R

L

+

 

NO!

 

 

R

L

+

 

NO!

Use the SUBWOOFER PRE OUT Subwoofer jack to connect a subwoofer with a

built-in power amplifier.

If your subwoofer does not have a built-in amplifier, connect an amplifier to the SUBWOOFER PRE OUT jack and the subwoofer to the amplifier.

Connecting to the speaker system A

Front speakers

Right Left

Surround speakers

Center speaker

Right

 

 

Left

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DO NOT connect the

power cord at this

 

 

AM

 

FM

ANTENNA

 

 

 

 

 

 

 

 

time.

 

 

 

75

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FRONT

 

FRONT

 

CENTER

SURROUND

 

 

VIDEO 3 VIDEO 2

VIDEO 1

DVD

MONITOR

SPEAKERS B

SPEAKERS A

SPEAKER

SPEAKERS

AC OUTLET

 

R

L

R

L

 

R

L

 

 

 

IN

OUT

IN

IN

OUT

 

 

 

 

 

 

 

 

DIGITAL INPUT

 

 

 

 

 

 

S VIDEO

 

 

 

 

 

 

 

OPTICAL COAXIAL

REMOTE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTROL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

IN

OUT

IN

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VIDEO

 

 

 

 

 

 

 

IN

OUT

IN

IN

IN

OUT

IN

FRONT SURR

L

 

 

 

 

 

 

L

SUBWOOFER

PRE OUT

R

TAPE

 

R

CD

VIDEO 3 VIDEO 2

VIDEO 1

DVD

CENTER

SUB WOOFER

Right Left

Front speakers

Connecting to the speaker system B

13

Image 13
Contents HT-R410 Important safeguards For U.S. models PrecautionsFor Canadian models Modèle pour les CanadienSupplied accessories FeaturesPrecautions Amplifier FeaturesAttach the battery cover Before using the unitUsing the remote controller Remote control sensor Receiver Standby indicator 30˚Index to parts and controls Index to parts and controls Rear panel Remote ControlTape IN/OUT Antenna 14Preset 2/3 button Remote controller= Mode buttons @ Adjust 2/3 buttonConnecting to audio/video equipment Do not connect the power cord at this time Connecting to audio/video equipmentCoaxial plug Coaxial cable Digital signal Signal flow Video Camera, Game Device, etc. VideoStandard speaker placement of the speaker system a Positioning speakers/Connecting speakersUsing the provided speaker labels How to connect to the speaker terminals Positioning speakers/Connecting speakersConnecting to the speaker system a Connecting to the speaker system BConnecting the supplied FM and AM indoor antennas Connecting antennasAdjusting the position of the FM indoor antenna Adjusting the position of the AM indoor antennaConnecting an FM outdoor antenna Connecting antennasConnecting an AM outdoor antenna Directional IinkagePower on/ready function Connections for remote control zPower off function Direct change functionEnjoying music or videos with the HT-R410 Before operating the remote controllerPress STANDBY/ON Selecting a sourceSetting the crossover frequency Speaker setupPress Speaker Adjust twice Speaker setup → Subwoofer Mode 1 Default Setting the subwoofer mode Press Subwoofer Mode on the unitSubwoofer Mode Adjusting each speaker’s relative volume balance Test toneChanging the default settings according to your connections Tuning in a weak frequency only for FM stations Tuning into a radio station Press TunerListening to the radio There are two ways to select radio stationsSelecting preset stations Presetting radio stationsPress Tuner to switch the input source to the tuner Listening to the radioListening through headphones Muting the sound remote controller only Press MutingVarious functions common to all the sources Before operating the SP A/SP BVarious functions common to all the sources Using the sleep timer remote controller only Press SleepChanging the display Press Display To fix the Auto to DTS or PCM Setting the input signal formatLevel 5/∞ Enjoying multi channel sources Using analog multi channel inputBefore operating Direct orEnjoying the listening modes Press one of the listening mode buttons Selecting the listening modeInput source and available listening mode Enjoying the listening modesBefore operating the remote control Audio adjust functionUsing the audio adjust functions Late Night Dolby Digital Audio adjust functionInput selector buttons Recording a sourceCamera Entering the manufacturer’s code Using the remote controller with your other AV componentsNumeric Using the remote controller with your other AV components Use the buttons as explained below Using the RC-518MTape VCRTV mode TV Amplifier Remote controller Symptoms Causes Remedies Pages TroubleshootingWhen incorrect operation is observed TroubleshootingSymptoms Causes Remedies OtherOnkyo Europe Electronics GmbH Specifications
Related manuals
Manual 4 pages 57.53 Kb

HT-R410 specifications

The Onkyo HT-R410 is a versatile and robust home theater receiver designed to enhance your audio-visual experience. Launched with features catered to both casual listeners and audiophiles alike, this receiver demonstrates why Onkyo has long been recognized for its commitment to quality and innovation.

At the heart of the HT-R410 is its 5.1 channel design, delivering an impressive total output power of 100 watts per channel. This allows users to fully immerse themselves in their favorite movies, music, and games with surrounding sound that matches the scale of the visuals. The receiver’s built-in Dolby Digital and DTS decoding ensures that audio tracks are reproduced with clarity and dynamism, bringing cinematic experiences to life within your living room.

One of the standout features of the Onkyo HT-R410 is its simple yet effective connectivity options. It includes multiple HDMI inputs, allowing users to hook up multiple devices such as game consoles, Blu-ray players, and streaming devices. The HDMI output supports both video and audio transmission, simplifying the setup and reducing cable clutter. Additionally, the receiver is equipped with legacy inputs, including composite and optical audio inputs, ensuring compatibility with various devices.

The HT-R410 adopts Onkyo’s renowned Dynamic Audio Amplification technology, which optimizes audio quality while minimizing distortion. This not only enhances listening experiences across all genres of music but also ensures a rich, accurate soundstage for films. The receiver's user-friendly interface, along with an easy-to-navigate remote control, allows users to switch between different audio settings and input sources seamlessly.

Furthermore, the Onkyo HT-R410 is designed with energy efficiency in mind, featuring a low standby power consumption rate, which is ideal for eco-conscious consumers. The device is also equipped with an intuitive graphic equalizer, enabling users to tailor sound profiles to suit their preferences or the specific acoustics of their viewing space.

In summary, the Onkyo HT-R410 is a feature-rich home theater receiver that combines quality sound with flexible connectivity. Its capabilities make it a perfect choice for anyone looking to create a cinematic experience at home without compromising on audio fidelity. Whether for action-packed films or serene musical compositions, the HT-R410 stands out for its performance and reliability.