Onkyo Enjoying music or videos with the HT-R410, Before operating the remote controller

Page 17

Enjoying music or videos with the HT-R410

Before connecting

•Make sure that all the connections from pages 10 to 16 are complete.

•Turning on the AV Receiver may cause a momentary power surge, which might interfere with other electrical equipment such as computers. If this happens, use a wall outlet on a different circuit.

STANDBY/ON

MASTER VOLUME dial

STANDBY/ON

 

 

 

STANDBY indicator

 

 

 

SP A

 

 

SP B

Before operating the remote controller

Press RCVR/TAPE.

 

 

Input selector

SPEAKERS A/B

Input Selector buttons

buttons

 

 

VOLUME 5/∞

Connecting the power

1. Connect the power cord to a wall outlet.

To a wall outlet

The HT-R410 enters standby mode.

The STANDBY indicator lights up.

2.Press STANDBY/ON.

The AV Receiver turns on.

The display on the AV Receiver’s front panel light. At the same time, the STANDBY indicator goes off.

Note

To turn off the AV Receiver, press STANDBY/ON. The AV Receiver enters standby mode. Be sure to set the volume to minimum before turning off the AV receiver.

Selecting a source

Before operating the remote controller, press RCVR/TAPE.

1.Press input selector button to select one of the following input sources:

•DVD

•VIDEO 1

•VIDEO 2

•VIDEO 3

•TAPE

•TUNER

•CD

e.g. When VIDEO 3 is selected.

A & B speakers indicators

Volume level

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.Ensure that the A and/or B indicator(s) for the speaker system(s) to be used are lit on the display.

If no indicator is lit, press SPEAKERS A/B on the unit or SP A/ SP B on the remote controller to select the speaker system(s) to be used.

3.Start playing the selected source.

See page 22 to listen to the tuner.

4.Press VOLUME 5/∞ on the remote controller or turn MASTER VOLUME dial on the unit to adjust the volume.

The volume can set to Min, 1 through 79, or Max.

About digital sound

If the equipment is digitally connected to the AV Receiver, the sound from the digital input will automatically be selected and reproduced instead of the analog sound as explained below.

The initial settings are as follows:

•When the DVD source is selected, the digital sound from the DIGITAL INPUT COAXIAL connector is reproduced.

•When the CD source is selected, the digital sound from the DIGITAL INPUT OPTICAL connector is reproduced.

See page 21 to change settings.

When the digital sound is reproduced, the ŸDIGITAL, DTS, or PCM (2 channel digital stereo) indicator lights up according to the received sound system in the AV Receiver’s display.

ŸDIGITAL PCM

DTS

When MD recorder is connected to the TAPE jacks, you can

 

switch the source from TAPE to MD (see page 21).

17

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents HT-R410 Important safeguards For U.S. models PrecautionsFor Canadian models Modèle pour les CanadienSupplied accessories FeaturesPrecautions Amplifier FeaturesAttach the battery cover Before using the unitUsing the remote controller Remote control sensor Receiver Standby indicator 30˚Index to parts and controls Index to parts and controls Rear panel Remote ControlTape IN/OUT Antenna 14Preset 2/3 button Remote controller= Mode buttons @ Adjust 2/3 buttonConnecting to audio/video equipment Do not connect the power cord at this time Connecting to audio/video equipmentCoaxial plug Coaxial cable Digital signal Signal flow Video Camera, Game Device, etc. VideoUsing the provided speaker labels Positioning speakers/Connecting speakersStandard speaker placement of the speaker system a How to connect to the speaker terminals Positioning speakers/Connecting speakersConnecting to the speaker system a Connecting to the speaker system BConnecting the supplied FM and AM indoor antennas Connecting antennasAdjusting the position of the FM indoor antenna Adjusting the position of the AM indoor antennaConnecting an FM outdoor antenna Connecting antennasConnecting an AM outdoor antenna Directional IinkagePower on/ready function Connections for remote control zPower off function Direct change functionEnjoying music or videos with the HT-R410 Before operating the remote controllerPress STANDBY/ON Selecting a sourcePress Speaker Adjust twice Speaker setupSetting the crossover frequency Speaker setup → Subwoofer Mode 1 Default Setting the subwoofer mode Press Subwoofer Mode on the unitSubwoofer Mode Adjusting each speaker’s relative volume balance Test toneChanging the default settings according to your connections Tuning in a weak frequency only for FM stations Tuning into a radio station Press TunerListening to the radio There are two ways to select radio stationsSelecting preset stations Presetting radio stationsPress Tuner to switch the input source to the tuner Listening to the radioListening through headphones Muting the sound remote controller only Press MutingVarious functions common to all the sources Before operating the SP A/SP BChanging the display Press Display Using the sleep timer remote controller only Press SleepVarious functions common to all the sources Level 5/∞ Setting the input signal formatTo fix the Auto to DTS or PCM Enjoying multi channel sources Using analog multi channel inputBefore operating Direct orEnjoying the listening modes Press one of the listening mode buttons Selecting the listening modeInput source and available listening mode Enjoying the listening modesUsing the audio adjust functions Audio adjust functionBefore operating the remote control Late Night Dolby Digital Audio adjust functionCamera Recording a sourceInput selector buttons Numeric Using the remote controller with your other AV componentsEntering the manufacturer’s code Using the remote controller with your other AV components Use the buttons as explained below Using the RC-518MTape VCRTV mode TV Amplifier Remote controller Symptoms Causes Remedies Pages TroubleshootingWhen incorrect operation is observed TroubleshootingSymptoms Causes Remedies OtherOnkyo Europe Electronics GmbH Specifications
Related manuals
Manual 4 pages 57.53 Kb

HT-R410 specifications

The Onkyo HT-R410 is a versatile and robust home theater receiver designed to enhance your audio-visual experience. Launched with features catered to both casual listeners and audiophiles alike, this receiver demonstrates why Onkyo has long been recognized for its commitment to quality and innovation.

At the heart of the HT-R410 is its 5.1 channel design, delivering an impressive total output power of 100 watts per channel. This allows users to fully immerse themselves in their favorite movies, music, and games with surrounding sound that matches the scale of the visuals. The receiver’s built-in Dolby Digital and DTS decoding ensures that audio tracks are reproduced with clarity and dynamism, bringing cinematic experiences to life within your living room.

One of the standout features of the Onkyo HT-R410 is its simple yet effective connectivity options. It includes multiple HDMI inputs, allowing users to hook up multiple devices such as game consoles, Blu-ray players, and streaming devices. The HDMI output supports both video and audio transmission, simplifying the setup and reducing cable clutter. Additionally, the receiver is equipped with legacy inputs, including composite and optical audio inputs, ensuring compatibility with various devices.

The HT-R410 adopts Onkyo’s renowned Dynamic Audio Amplification technology, which optimizes audio quality while minimizing distortion. This not only enhances listening experiences across all genres of music but also ensures a rich, accurate soundstage for films. The receiver's user-friendly interface, along with an easy-to-navigate remote control, allows users to switch between different audio settings and input sources seamlessly.

Furthermore, the Onkyo HT-R410 is designed with energy efficiency in mind, featuring a low standby power consumption rate, which is ideal for eco-conscious consumers. The device is also equipped with an intuitive graphic equalizer, enabling users to tailor sound profiles to suit their preferences or the specific acoustics of their viewing space.

In summary, the Onkyo HT-R410 is a feature-rich home theater receiver that combines quality sound with flexible connectivity. Its capabilities make it a perfect choice for anyone looking to create a cinematic experience at home without compromising on audio fidelity. Whether for action-packed films or serene musical compositions, the HT-R410 stands out for its performance and reliability.
Top Page Image Contents