PLUS Vision U2-1130/U2-1110 user manual I n g t h e u n i t c o n t i n u e d

Page 18

U s i n g t h e u n i t ( c o n t i n u e d )

Using the adjusters to adjust the height balance

There are two front adjusters and one rear adjuster.

1If you need to lower the position of the projected image, pull out the leg of the rear adjuster.

2Hold the front sides of the unit, then adjust the height of the projected image.

While adjusting the height, the rear adjuster should remain on the table.

3Press the left and right buttons by the front ad- justers at the same time to loosen the adjuster legs.

Adjusting the distorted picture

The upper distortion of the picture will be corrected as you see the illustration below.

The menu screen shape is not changed by the keystone

correction even when displayed.

→←

The front adjuster legs will loosen and be extended.

4Release the buttons to fix the position of the front adjuster legs.

5 To fine-adjust the height and balance, turn each

7 Adjust the image size with the zoom ring,

foot of the front adjuster legs.

then adjust the focus with the focus ring.

 

 

 

 

 

 

 

2

Zoom ring

MOUSE

 

 

 

 

RGB IN

 

 

 

 

PC AUDIO

S-VIDEO

 

 

 

 

 

 

 

 

VIDEO

AUDIO

 

 

 

 

 

 

L/MONO

R

 

Down

 

1

3

Up

 

4

Up Down

5

6 (If the vertical offset cannot be adjusted completely with the adjusters)

Press KEYSTONE + or – to correct the offset (keystoning) image.

You can also correct the keystoning effect with the menu operation (see page 24).

MAGNIFY

KEYSTONE

VOLUME

+

+

+

–

–

–

PLUS

Note

The maximum correction value is 29° including the optical correction value.

Focus ring

8 Change the unit setting to suit the method and source selected in step 4.

The following settings can be made using the menu operation.

The menu can be displayed in English, Deutsch,

Français, Italiano, Español, Svenska, or . (The standard setting is English.) See page 24.

•For basic menu operation, see page 23.

•To see an overview of the menu structure, see page 22.

•Select the type of projection

If the projected image is horizontally reversed or upside down, change the projection type. See page 24.

•When the input source is VIDEO or S-

VIDEO

Select the color system. See page 24.

•When the input source is RGB

Adjust the projected image from the computer. The resolution most suitable for the incoming signals is automatically selected.

However, if any vertical banding, noise, dot interference, or crosstalk appears on the screen, manually adjust “PICTURE ADJ,” then “FINE PICTURE” using the menus. See page 27.

E – 16

Page 17 Page 19
Image 18
Page 17 Page 19
Contents U2-1130/U2-1110 Plus Corporation U2-1130/U2-1110 English Installation PrecautionsImportant Safeguards Power SupplyB l e o f c o n t e n t s E c k i n g t h e P p l i e d a c c e s s o r i e s Power cable mains lead 1.8 m/5.9 ftA t u r e s Serial mouse cable Mouse adapter For IBM PS/2Remote control effective range E p a r i n g t h e M o t e c o n t r o lInserting the batteries Top, front and side panel view RGB in connectorR t s a n d c o n t r o l s Menu buttonBottom Lamp cover securing screw Rear adjusterRear and side panel view Built-in Security SlotClick button 14 Freeze button Mute buttonProjecting distance and image size InstallationPositioning the unit ScreenInstallation c o n t i n u e d Using the ceiling mounting fixturesUnits terminal panel N n e c t i o n sBefore connecting ConnectorN n e c t i n g a P C o r M a c i n t o s h Modifying the DIP switch setting for Macintosh 3 4 5How to connect to the IBM PC/AT computer How does the remote control operate the computer?Connecting the computer to the Mouse connector of the unit How to connect to the IBM PS/2 or Macintosh computerBefore starting Adjust the position and height of the unitI n g t h e u n i t View from the topAdjust the image size with the zoom ring Then adjust the focus with the focus ringI n g t h e u n i t c o n t i n u e d After using the unit AmberWindows 98/Windows WindowsMacintosh Turning off the image and muting the sound temporarily Adjusting the volume of the units speakerUsing the laser pointer Freezing a moving picturePress Magnify + Enlarging the picturePress Pointer Press MagnifyPointer When the input source is Video or S-VIDEO N u s t r u c t u r eOperating using the unit L e c t i n g a O j e c t i o n t y p e R r e c t i n g t h e Y s t o n i n g e f f e c tL e c t i n g a m e n u l a n g u a g e L e c t i n g t h e c o l o r s y s t e mL e c t i n g t h e p o i n t e r t y p e L e c t i n g t h e b a c k g r o u n dJ u s t i n g t h e v o l u m e Timing Chart Adjusting the clock frequency Setting the input source to RGBSetting Auto Mode to OFF for manual ad- justment Adjusting the clock phaseJ u s t i n g t h e C t u r e e l e m e n t s L e c t i n g t h e p i c t u r e t y p eT i v a t i n g t h e p o w e r s a v i n g f u n c t i o n T i v a t i n g t h e o n s c r e e n f u n c t i o nI c k s t a r t i n g t h e u n i t Resetting the lamp usage hours to zero E c k i n g h o u r s o f l a m p u s a g eS e t t i n g t o t h e f a c t o r y s e t t i n g s Troubleshooting Common Problems & SolutionsStatus indicator Status Light MessagesLamp cartridge replacement procedure P l a c i n g t h e l a m p c a r t r i d g eStep Specification s OpticalSub Pin Assignments PC 15-Pin mini D-SubDimensions U2-1130U2-1110 Plus Corporation
Top Page Image Contents