PLUS Vision U2-1130/U2-1110 Precautions, Important Safeguards, Installation, Power Supply

Page 4

I M P O R T A N T S A F E T Y I N F O R M A T I O N

Precautions

Please read this manual carefully before using your PLUS U2-1130/U2-1110 Data Projector and keep the manual handy for future reference.

Your serial number is located next to the main power switch on the back of the unit. Record it here:

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PLUS SERVICE PERSONNEL.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EX- POSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUT- LET UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABI- NET. THERE ARE HIGH-VOLTAGE COMPO- NENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED PLUS SERVICE PER- SONNEL.

DOC Compliance Notice

This Class A digital apparatus complies with Canadian ICES-003.

Important Safeguards

RF Interference

WARNING

The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by PLUS Technologies in this manual. Failure to comply with this government regulation could void your right to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Warning

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

These safety instructions are to ensure the long life of the unit and to prevent fire and shock. Please read them carefully and heed all warnings.

Installation

•For best results, use the unit in a darkened room.

•Place the unit on a flat, level surface in a dry area away from dust and moisture.

•Do not place the unit in direct sunlight, near heaters or heat radiating appliances.

•Exposure to direct sunlight, smoke or steam can harm internal components.

•Handle the unit carefully. Dropping or jarring can damage inter- nal components.

•Do not place heavy objects on top of the unit.

•If installing the unit on the ceiling:

–The ceiling must be strong enough to support the unit and the installation must be in accordance with any local building codes.

–The unit must be installed by qualified PLUS service person- nel.

Power Supply

•The unit is designed to operate on a power supply of 100 to 120 and 220 to 240 V 50/60 Hz AC. Ensure that your power supply fits these requirements before attempting to use the unit.

•For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be accessible.

•Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or fire.

•Disconnect the power cable (mains lead) from the power outlet after using the unit.

Before disconnecting the power cable, make sure that the POWER indicator lights in amber (not in green).

E – 2

Page 3 Page 5
Image 4
Page 3 Page 5
Contents U2-1130/U2-1110 Plus Corporation U2-1130/U2-1110 English Precautions Important SafeguardsInstallation Power SupplyB l e o f c o n t e n t s Power cable mains lead 1.8 m/5.9 ft A t u r e sE c k i n g t h e P p l i e d a c c e s s o r i e s Serial mouse cable Mouse adapter For IBM PS/2E p a r i n g t h e M o t e c o n t r o l Remote control effective rangeInserting the batteries RGB in connector R t s a n d c o n t r o l sTop, front and side panel view Menu buttonLamp cover securing screw Rear adjuster Rear and side panel viewBottom Built-in Security SlotClick button 14 Freeze button Mute buttonInstallation Positioning the unitProjecting distance and image size ScreenInstallation c o n t i n u e d Using the ceiling mounting fixturesUnits terminal panel N n e c t i o n sConnector Before connectingN n e c t i n g a P C o r M a c i n t o s h Modifying the DIP switch setting for Macintosh 3 4 5How does the remote control operate the computer? Connecting the computer to the Mouse connector of the unitHow to connect to the IBM PC/AT computer How to connect to the IBM PS/2 or Macintosh computerAdjust the position and height of the unit I n g t h e u n i tBefore starting View from the topThen adjust the focus with the focus ring Adjust the image size with the zoom ringI n g t h e u n i t c o n t i n u e d After using the unit AmberWindows Windows 98/WindowsMacintosh Adjusting the volume of the units speaker Using the laser pointerTurning off the image and muting the sound temporarily Freezing a moving pictureEnlarging the picture Press PointerPress Magnify + Press MagnifyPointer When the input source is Video or S-VIDEO N u s t r u c t u r eOperating using the unit R r e c t i n g t h e Y s t o n i n g e f f e c t L e c t i n g a m e n u l a n g u a g eL e c t i n g a O j e c t i o n t y p e L e c t i n g t h e c o l o r s y s t e mL e c t i n g t h e b a c k g r o u n d L e c t i n g t h e p o i n t e r t y p eJ u s t i n g t h e v o l u m e Timing Chart Setting the input source to RGB Setting Auto Mode to OFF for manual ad- justmentAdjusting the clock frequency Adjusting the clock phaseJ u s t i n g t h e C t u r e e l e m e n t s L e c t i n g t h e p i c t u r e t y p eT i v a t i n g t h e o n s c r e e n f u n c t i o n T i v a t i n g t h e p o w e r s a v i n g f u n c t i o nI c k s t a r t i n g t h e u n i t E c k i n g h o u r s o f l a m p u s a g e Resetting the lamp usage hours to zeroS e t t i n g t o t h e f a c t o r y s e t t i n g s Troubleshooting Common Problems & SolutionsStatus indicator Status Light MessagesP l a c i n g t h e l a m p c a r t r i d g e Lamp cartridge replacement procedureStep Specification s OpticalSub Pin Assignments PC 15-Pin mini D-SubU2-1130 DimensionsU2-1110 Plus Corporation
Top Page Image Contents