PLUS Vision U2-1130/U2-1110 user manual Status Light Messages, Status indicator

Page 34

W h e n t h e S T A T U S i n d i c a t o r l i g h t s o r f l a s h e s

STATUS POWER

STATUS indicator

MENU ENTER

SELECT

UP

DOWN

Status Light Messages

Condition	Status

OFF	Normal

On Continually	The lamp usage has exceeded 1000 hours of operation and should be replaced.

Flashing Very Rapidly (On and off	•	The lamp cover is not correctly attached. Replace it correctly.
in a cycle of 1 sec.)

Flashing Rapidly	•	The temperature protector has been triggered. If the room temperature is high,
(On and off in a cycle of 4 sec.)		move the unit to a cool location. If the temperature within the unit is high, check the
		cooling fan ventilation slots and the ventilation slots on the bottom of the unit. If
		any of the slots are blocked, remove whatever is blocking them.
	•	The temperature protector has been triggered. If you try to turn on the unit immedi-
		ately after turning off, sometimes the power does not come on. If this happens, wait
		at least one minute, then turn on the unit again.
	•	The lamp lighting voltage error detection protector has been triggered. Wait at
		least one minute before turning on the unit again. If this does not solve the problem,
		please contact your dealer.

Flashing Slowly (On and off in a	The cooling fan has stopped. Contact your PLUS dealer for service.
cycle of 8 sec.)

Flashing Very Slowly (On and off in	The lamp is not turned on.
a cycle of 12 sec.)	• The unit was turned on immediately after being turned off. Turn off the unit, wait at
		least one minute, then turn on the unit again.
	•	The lamp is dead. Replace the lamp cartridge. (See page 33.)

E – 32

Image 34

Contents U2-1130/U2-1110 Plus Corporation U2-1130/U2-1110 English Installation PrecautionsImportant Safeguards Power SupplyB l e o f c o n t e n t s E c k i n g t h e P p l i e d a c c e s s o r i e s Power cable mains lead 1.8 m/5.9 ftA t u r e s Serial mouse cable Mouse adapter For IBM PS/2E p a r i n g t h e M o t e c o n t r o l Remote control effective rangeInserting the batteries Top, front and side panel view RGB in connectorR t s a n d c o n t r o l s Menu buttonBottom Lamp cover securing screw Rear adjusterRear and side panel view Built-in Security SlotClick button 14 Freeze button Mute buttonProjecting distance and image size InstallationPositioning the unit ScreenInstallation c o n t i n u e d Using the ceiling mounting fixturesUnits terminal panel N n e c t i o n sConnector Before connectingN n e c t i n g a P C o r M a c i n t o s h Modifying the DIP switch setting for Macintosh 3 4 5How to connect to the IBM PC/AT computer How does the remote control operate the computer?Connecting the computer to the Mouse connector of the unit How to connect to the IBM PS/2 or Macintosh computerBefore starting Adjust the position and height of the unitI n g t h e u n i t View from the topThen adjust the focus with the focus ring Adjust the image size with the zoom ringI n g t h e u n i t c o n t i n u e d After using the unit AmberWindows Windows 98/WindowsMacintosh Turning off the image and muting the sound temporarily Adjusting the volume of the units speakerUsing the laser pointer Freezing a moving picturePress Magnify + Enlarging the picturePress Pointer Press MagnifyPointer When the input source is Video or S-VIDEO N u s t r u c t u r eOperating using the unit L e c t i n g a O j e c t i o n t y p e R r e c t i n g t h e Y s t o n i n g e f f e c tL e c t i n g a m e n u l a n g u a g e L e c t i n g t h e c o l o r s y s t e mL e c t i n g t h e b a c k g r o u n d L e c t i n g t h e p o i n t e r t y p eJ u s t i n g t h e v o l u m e Timing Chart Adjusting the clock frequency Setting the input source to RGBSetting Auto Mode to OFF for manual ad- justment Adjusting the clock phaseJ u s t i n g t h e C t u r e e l e m e n t s L e c t i n g t h e p i c t u r e t y p eT i v a t i n g t h e o n s c r e e n f u n c t i o n T i v a t i n g t h e p o w e r s a v i n g f u n c t i o nI c k s t a r t i n g t h e u n i t E c k i n g h o u r s o f l a m p u s a g e Resetting the lamp usage hours to zeroS e t t i n g t o t h e f a c t o r y s e t t i n g s Troubleshooting Common Problems & SolutionsStatus indicator Status Light MessagesP l a c i n g t h e l a m p c a r t r i d g e Lamp cartridge replacement procedureStep Specification s OpticalSub Pin Assignments PC 15-Pin mini D-SubU2-1130 DimensionsU2-1110 Plus Corporation