PLUS Vision U2-1130/U2-1110 user manual After using the unit, Amber

Page 19

The horizontal and vertical positions of the image can also be adjusted manually. See page 27.

If you have set “AUTO MODE” to “OFF” to carry out the above described adjustments (see page 27 for details), you can choose to project the image at the original size of the incoming signal resolution. (Normally, the image is enlarged or reduced to the most suitable size automatically.) See page 27.

9 Adjust the picture elements (see page 28), then select the picture type according to the video content (see page 28).

10 Start using the unit.

The following functions are available while using the unit:

•Adjusting the volume of the unit's speaker (see pages 19 and 25),

•Using the laser pointer (see page 19),

•Turning off the image and muting the sound temporarily (see page 19),

•Freezing a moving picture (see page 19),

•Enlarging the picture (see page 20), and

•Enlarging the picture after selecting the portion you wish to enlarge (see page 21).

Note

If “POWER OFF” is set to “ON” (see page 29), the image will be turned off if the unit has been left unoperated for five minutes with an RGB input source.

If the image is suddenly turned off while projecting a computer image, the computer’s screen saver or power management function may be activated.

After using the unit

1 Press POWER OFF on the remote control, or POWER on the unit, for two to three seconds.

When you have turned off the unit, the POWER indicator will start flashing then turn to amber in one minute.

Never disconnect the power cable while the POWER indicator is flashing.

 

 

POWER

OFF

POWER

ON

VIDEO

S-VIDEO

Green light flashes

 

 

(About one minute)

 

 

↓

RGB

 

Then lights steadily

 

 

in amber

Notes

•Neither POWER ON on the remote control nor POWER on the unit operate while the POWER indicator is flashing.

•Wait at least one minute before turning on the unit again. POWER ON on the remote control or POWER on the unit may not operate if you try to turn on the unit again within one minute after turning off the unit.

2 After the POWER indicator stops flashing and turns to amber, disconnect the power cable from the wall outlet, then from the unit.

The POWER indicator goes out.

Note

Hold the plug when disconnecting the power cable. Never pull the cord.

(Continued on next page.)

E – 17

Page 18 Page 20
Image 19
Page 18 Page 20
Contents U2-1130/U2-1110 Plus Corporation U2-1130/U2-1110 English Power Supply PrecautionsImportant Safeguards InstallationB l e o f c o n t e n t s Serial mouse cable Mouse adapter For IBM PS/2 Power cable mains lead 1.8 m/5.9 ftA t u r e s E c k i n g t h e P p l i e d a c c e s s o r i e sE p a r i n g t h e M o t e c o n t r o l Remote control effective rangeInserting the batteries Menu button RGB in connectorR t s a n d c o n t r o l s Top, front and side panel viewBuilt-in Security Slot Lamp cover securing screw Rear adjusterRear and side panel view BottomFreeze button Mute button Click button 14Screen InstallationPositioning the unit Projecting distance and image sizeUsing the ceiling mounting fixtures Installation c o n t i n u e dN n e c t i o n s Units terminal panelConnector Before connectingN n e c t i n g a P C o r M a c i n t o s h 3 4 5 Modifying the DIP switch setting for MacintoshHow to connect to the IBM PS/2 or Macintosh computer How does the remote control operate the computer?Connecting the computer to the Mouse connector of the unit How to connect to the IBM PC/AT computerView from the top Adjust the position and height of the unitI n g t h e u n i t Before startingThen adjust the focus with the focus ring Adjust the image size with the zoom ringI n g t h e u n i t c o n t i n u e d Amber After using the unitWindows Windows 98/WindowsMacintosh Freezing a moving picture Adjusting the volume of the units speakerUsing the laser pointer Turning off the image and muting the sound temporarilyPress Magnify Enlarging the picturePress Pointer Press Magnify +Pointer N u s t r u c t u r e When the input source is Video or S-VIDEOOperating using the unit L e c t i n g t h e c o l o r s y s t e m R r e c t i n g t h e Y s t o n i n g e f f e c tL e c t i n g a m e n u l a n g u a g e L e c t i n g a O j e c t i o n t y p eL e c t i n g t h e b a c k g r o u n d L e c t i n g t h e p o i n t e r t y p eJ u s t i n g t h e v o l u m e Timing Chart Adjusting the clock phase Setting the input source to RGBSetting Auto Mode to OFF for manual ad- justment Adjusting the clock frequencyL e c t i n g t h e p i c t u r e t y p e J u s t i n g t h e C t u r e e l e m e n t sT i v a t i n g t h e o n s c r e e n f u n c t i o n T i v a t i n g t h e p o w e r s a v i n g f u n c t i o nI c k s t a r t i n g t h e u n i t E c k i n g h o u r s o f l a m p u s a g e Resetting the lamp usage hours to zeroS e t t i n g t o t h e f a c t o r y s e t t i n g s Common Problems & Solutions TroubleshootingStatus Light Messages Status indicatorP l a c i n g t h e l a m p c a r t r i d g e Lamp cartridge replacement procedureStep Optical Specification sPC 15-Pin mini D-Sub Sub Pin AssignmentsU2-1130 DimensionsU2-1110 Plus Corporation
Top Page Image Contents