Onkyo TX-DS484 Making antenna connections, Directional Iinkage, Assembling the AM loop antenna

Page 12

Making antenna connections

	Outdoor	Indoor
	antenna	antenna
		300 ohms
		ribbon wire
1	2	3
			✦
		✦ ✦		✦
		✦✦	✦ ✦	✦
		✦ ✦
			6	3	6
	Slit B	mm mm mm
	Slit B		15mm
	Wire A	1
	Wire A
	Slit C
		2

Connecting the antenna cable to the 75/300 ohm antenna adapter (Worldwide models)

Connecting the 300 ohm ribbon wire:

Loosen the screws and wrap the wire around these screws. Then tighten the screws with a screwdriver.

Connecting the coaxial cable:

1.With your ﬁngernail or a small screwdriver, press the stoppers outward and remove the cover.

2.Remove the transformer wire A from slit B and insert it into slit C.

3.Prepare the coaxial cable as shown in the diagram.

Connect the 75/300 ohm antenna adapter to the coaxial cable. 1Insert the end of the cable.

2Clamp it in place with pliers.

4.Re-install the cover.

Directional linkage type splitter

To TX-DS484

To TV (or VCR)

Directional Iinkage

Do not use the same antenna for both FM and TV (or VCR) recep- tion since the FM and TV (or VCR) signals can interfere with each other. If you must use a common FM/TV (or VCR) antenna, use a directional linkage type splitter.

Insert into the hole.

1

2

3

Assembling the AM loop antenna

Assemble the loop antenna as shown in the illustration.

•Refer to the next page for details on connecting the AM loop antenna.

Connecting the antenna cable

1.Press down the lever.

2.Insert the wire into the hole.

3.Release the lever to replace it.

12

Image 12

Contents TX-DS484 Important Safeguards Precautions Features Supplied accessoriesMemory Preservation Setting the AM tuning step frequency Worldwide models only Setting the Voltage selector Worldwide models onlyInstalling the remote controller batteries Using the remote controllerAudio equipment connections Input Output RECVideo equipment connections Digital audio connectionsConnecting other devices Decoder with 5.1 channel outputConnecting other devices Connections for remote controlAC outlet connection Connecting speakers Connecting the speaker cableOr B 6 ohms min./speaker Ohms min./speakerConnecting the power Connecting the powerPlug the power cord into an AC wall outlet. Note Positioning speakersConnecting the antenna cable Making antenna connectionsDirectional Iinkage Assembling the AM loop antennaConnecting the included antennas Connecting an FM outdoor antennaConnecting an AM outdoor antenna Making antenna connectionsSpeaker setup Speaker setupSpeaker setup Test Tone Remote controller only Press the Test Tone button to complete adjustmentParameter selector Press the Test Tone buttonSelecting a sound source When Multi channel input is selected as a source Using the Power On Volume functionSelecting a sound source Press the Parameter Controller √ or button to select onSwitching between digital and analog inputs Adjusting the tone BASS, TrebleListening through headphones Phones Sleep function Remote controller onlyTo enjoy Surround mode or Stereo mode Before Using Surround ModeSurround Mode button Late Night button Volume knobTo enjoy Surround mode or Stereo mode Selecting a Surround modeSetting the Surround mode parameters Setting the input signal formatAuto Auto Detect mode Tuning in a radio station Manual tuningListening to a stereo radio station FM mode Receiving RDS European model onlyUsing preset radio stations Selecting a preset stationCancelling preset stations Programming radio stationsRecording a source Recording an audio sourceRecording a source Adding new sound to a video tape during video editingTroubleshooting guide Trouble Cause Remedy SeeSpeciﬁcations Amplifier SectionControl positions and names Front panel DisplayRemote controller RC-427S Audio muting button Muting 17Using the remote controller Using an Onkyo tape deckUsing an Onkyo CD player Using an Onkyo DVD playerOnkyo U.S.A. Corporation