Onkyo TX-DS484 Test Tone Remote controller only, Parameter selector, Press the Test Tone button

Page 16

Speaker setup

9

 

 

PARAMETER CONTROLLER

 

or

PARAMETER SELECTOR

 

or

 

 

10

 

 

PARAMETER CONTROLLER

 

or

 

 

PARAMETER SELECTOR

 

 

1, 3

TEST

 

TONE

 

2

CH SEL

TEST

 

 

TONE

 

LEVEL

 

9.Press the PARAMETER SELECTOR® button to display the LFE LEVEL parameter, and press the PARAMETER CONTROLLER √/® buttons to set the value.

You can set the LFE LEVEL parameter for the Dolby digital or DTS playback.

In general, leave this parameter to 0dB.

Pressing the PARAMETER CONTROLLER √/® buttons repeatedly toggles the values. Display the desired value.

With the Dolby digital sound, the parameter value changes as

shown on the left. With the DTS sound, the parameter value changes in the following order: +10dB, 0dB, –∞dB.

Also, refer to “LFE level attenuation” on page 22.

10.Press the PARAMETER SELECTOR ® button. The

POWER ON VOLUME ON/OFF parameter appears.

Press the PARAMETER CONTROLLER √/® buttons to toggle between ON and OFF.

ON: Power On Volume function is enabled.

OFF: Power On Volume function is disabled.

Display the desired setting and press the PARAMETER SELECTOR ® button.

Refer to page 18 for more information on the Power On Volume function.

Note:

Even if the parameter has already been set to ON, turn it OFF, then turn it ON again to enable the Power On Volume function.

Test Tone (Remote controller only)

Use the remote controller and produce the test tone to adjust the level of the connected speakers.

1.Press the TEST TONE button.

Each speaker produces the test tone (pink noise) in the follow- ing order:

LEFT

CENTER

RIGHT

(Front L ch)

(Center ch)

(Front R ch)

SUBWOOFER

L-SURROUND

R-SURROUND

(Subwoofer)

(L-Surround)

(R-Surround)

2.To adjust the level of each speaker, press the CH SEL button to select a speaker and press the LEVELπ/† buttons to raise or lower the level.

The test tone should sound at the same level when you hear it in your listening position. You can adjust the level in the range between –12dB and +12dB.

3.Press the TEST TONE button to complete adjustment.

Parameter selector

This chart shows how the display changes when the PARAMETER SELECTOR buttons are pressed. Selecting a parameter and pressing the PARAMETER CONTROLLER button will change the value or setting for the selected parameter.

START

 

 

Subwoofer

YES / NO

 

 

 

 

 

 

 

 

 

 

 

PARAMETER SELECTOR

 

 

PARAMETER SELECTOR

 

 

 

 

 

 

 

 

 

 

FRONT Speaker LARGE / SMALL

Center Speaker LARGE / SMALL / NONE

Surround Speaker LARGE / SMALL / NONE

FRONT Speaker Distance

0.3 ~ 9m, 1 ~ 30ft

Center Speaker Distance

0.3 ~ 9m, 1 ~ 30ft

Surround Speaker Distance

0.3 ~ 9m, 1 ~ 30ft

LFE Level Attenuator Dolby Digital:

0dB / –10dB / –∞dB DTS:

+10dB / 0dB / –∞dB

POWER ON VOLUME ON / OFF

QUIT

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents TX-DS484 Important Safeguards Precautions Supplied accessories FeaturesMemory Preservation Setting the AM tuning step frequency Worldwide models only Setting the Voltage selector Worldwide models onlyInstalling the remote controller batteries Using the remote controllerAudio equipment connections Input Output RECVideo equipment connections Digital audio connectionsConnecting other devices Decoder with 5.1 channel outputConnections for remote control Connecting other devicesAC outlet connection Connecting speakers Connecting the speaker cableOr B 6 ohms min./speaker Ohms min./speakerConnecting the power Connecting the powerPlug the power cord into an AC wall outlet. Note Positioning speakersConnecting the antenna cable Making antenna connectionsDirectional Iinkage Assembling the AM loop antennaConnecting the included antennas Connecting an FM outdoor antennaConnecting an AM outdoor antenna Making antenna connectionsSpeaker setup Speaker setupSpeaker setup Test Tone Remote controller only Press the Test Tone button to complete adjustmentParameter selector Press the Test Tone buttonSelecting a sound source When Multi channel input is selected as a source Using the Power On Volume functionSelecting a sound source Press the Parameter Controller √ or button to select onSwitching between digital and analog inputs Adjusting the tone BASS, TrebleListening through headphones Phones Sleep function Remote controller onlyTo enjoy Surround mode or Stereo mode Before Using Surround ModeSurround Mode button Late Night button Volume knobTo enjoy Surround mode or Stereo mode Selecting a Surround modeSetting the input signal format Setting the Surround mode parametersAuto Auto Detect mode Tuning in a radio station Manual tuningListening to a stereo radio station FM mode Receiving RDS European model onlyUsing preset radio stations Selecting a preset stationCancelling preset stations Programming radio stationsRecording a source Recording an audio sourceRecording a source Adding new sound to a video tape during video editingTroubleshooting guide Trouble Cause Remedy SeeSpecifications Amplifier SectionControl positions and names Front panel DisplayRemote controller RC-427S Audio muting button Muting 17Using the remote controller Using an Onkyo tape deckUsing an Onkyo CD player Using an Onkyo DVD playerOnkyo U.S.A. Corporation
Top Page Image Contents