Planar C3215 LBA Mode Control, Bit I/O, Transfer Mode, Ultra DMA Mode, USB Legacy Support

Page 31

LBA Mode Control

When enabled, this option allows the System BIOS to reference hard disk data as logical blocks instead of using the traditional Cylinders/Heads/Sectors (CHS) method. This option can only be used if both the hard disk being configured and the operating system support Logical Block Addressing (LBA). If disabled, then CHS mode is used. Note that autotyping may change this value if the hard disk reports that it supports LBA. The default is Disabled.

32-Bit I/O

This option allows the System BIOS to access the hard disk controller with 32-bit I/O accesses, increasing system performance, This selection is not affected by autotyping. If the PCI IDE con- troller in the chipset is being used, then this option should be set to Enabled to maximize system performance. If an ISAbus IDE controller is installed in the system, then this option should be set to Disabled. The default is Disabled.

Transfer Mode

This option selects the mode that the System BIOS uses to access the hard disk. The selections are: Standard, Fast PIO 1, Fast PIO 2, Fast PIO 3, and Fast PIO 4.

Older hard disks only support Standard. Newer hard disks adhering to Fast ATA or Enhanced IDE specifications may support the fast programmed I/O or DMA modes. Note that autotyping may change this value depending on the transfer modes that the hard disk supports. The fast DMA modes take full advantage of the onboard bus master hard disk controller and yields the highest performance when used in conjunction with multitasking operating systems that support it. The default is Standard.

Ultra DMA Mode

This option selects the Ultra DMA Mode that the System BIOS uses to access the hard disk. The selections are: Disabled, Mode 0, Mode 1, and Mode 2. The default is Disabled.

USB Legacy Support

This option allows for USB support of non-USB supported operating systems. Enabling of this option can cause system conflicts with operating systems that support USB. The default is

Disabled.

20Planar Clean Screen II PC User’s Manual

Image 31
Contents User’s Manual Integrated Computer with LCD Color Display USER’S ManualIi Planar Clean Screen II PC User’s Manual Federal Communications Commission FCC Requirements Commencement of WarrantyCanadian Emissions Requirements Installation Duration of WarrantyPlace of Repair or Replacement Limitation of WarrantyTable of Contents Vi Planar Clean Screen II Screen PC User’s Manual Reference Guide ViiWhat if I’m missing something? Before You BeginWhat’s in the box? What’s in this manual?Clean Screen II Mounts and Accessories Safety InstructionsConnections Bottom Front PanelChapter Four System Setup Chapter One The Installation ExpressClean Screen II Facts Chapter Two The Clean Screen II PCWelcome Chapter Two The Clean Screen II PC Inside Back HousingChapter Two The Clean Screen II PC Removing the Back Housing Chapter Three Hardware Installation and ReplacementTo install a memory module Installing MemoryTo remove a memory module Range CPU address Region Cached Memory MapReplacing the Hard Disk Drive Installing the new hard diskRemoving the existing hard disk Flash memory. See Chapter Five Bios Setup Replacing the BatteryReplacing the Fuse Mounting the Clean Screen PC Card Slot Chapter Four System SetupConnecting the Keyboard Connecting PeripheralsUSB Connection Power SupplyPower Cord Selection Floppy Drive ConnectionDriver Overview Powering Up the Clean Screen II PCPower On Setup F2Entering the Bios Setup Program Chapter Five Bios SetupSetup Screens Main Menu Extended Memory Boot Options Sub-MenuBoot-Time Diagnostic Screen System MemoryMulti-Sector Transfers Primary Master/Slave Sub-Menus under Main MenuAutotype Fixed Disk TypeBit I/O LBA Mode ControlTransfer Mode Ultra DMA ModeBoot Options Sub-Menu under Main Menu Large Disk Access Mode Device Configuration Sub-MenuInstalled OS Win Reset Configuration DataPS2 Mouse PCI Configuration Sub-MenuLegacy USB Support Device Configuration Sub-Menu under Advanced Menu Floppy Disk Controller Standby Timeout Power Management MenuPower Savings Idle ModeResume Time Resume On TimeIDE Monitoring Removable Format Boot MenuHard Drive Removable DevicesExit Menu Approved cleaning solutions include Chapter Six Care and CleaningMaintenance Tips Cleaning TipsAppendix a Product Specifications Optional Resistive Touch Screen Controller External Serial PortsUSB Ports Floppy Disk Drive PortDescription Pin Environmental SpecificationsAssigned and Available IRQs Appendix B Programming InterfaceDMAs Address Device Address ListTroubleshooting Procedure Appendix C TroubleshootingAnti-Virus Alert Causes Boot FailuresProblems After the System Has Been Running Correctly Problems At Initial System StartupProblems Operating PC Cards Problems Running New Application SoftwareProblems with Ethernet What happens What to do Problems and SuggestionsSee Problems at Initial System Start-up Error Message / Beeps Explanation Error and Information MessagesPost Error Message ExplanationMessage Explanation PCI Configuration Status and Error MessagesResetting the System Appendix D Touch Screen optional Cmos ConfigurationFor Further Information and Driver Updates For ServiceAppendix E Technical Support Planar Clean Screen II PC User’s Manual Canada

C3215 specifications

The Planar C3215 is a high-performance display solution designed for a variety of professional and commercial applications. With its sleek design and advanced functionalities, the C3215 stands out as an ideal choice for environments ranging from corporate settings to retail spaces.

One of the primary features of the Planar C3215 is its impressive display quality. The monitor boasts a resolution of 1920x1080 pixels, providing vibrant colors and sharp images that enhance the viewing experience. The LED-backlit technology further improves brightness and energy efficiency, ensuring that users benefit from striking visuals while minimizing power consumption.

The C3215 display is equipped with a wide viewing angle, utilizing in-plane switching (IPS) technology that allows for consistent color accuracy and clarity from various angles. This feature makes it particularly suitable for collaborative workspaces or public displays, where multiple viewers may be observing the screen simultaneously from different positions.

In terms of connectivity, the C3215 is versatile. It offers multiple input options, including HDMI, DisplayPort, and VGA, allowing seamless integration with a variety of devices such as computers, laptops, and media players. This flexibility ensures that users can easily switch between different sources without hassle.

Durability is another key aspect of the C3215. The screen is designed for continuous usage, making it suitable for 24/7 operation in demanding environments. Its robust construction means it can withstand the rigors of daily use, ensuring longevity and reliability.

Moreover, the Planar C3215 incorporates advanced anti-glare technology, reducing reflections and providing users with a clearer view of the content, even in brightly lit settings. This characteristic is essential for environments where lighting conditions can be unpredictable.

For those concerned about installation, the C3215 is designed with user convenience in mind. It supports multiple mounting options, including VESA mounting, which allows users to easily mount the display on walls or use it in conjunction with various stand solutions.

In summary, the Planar C3215 is a feature-rich display that combines superb image quality, durability, and flexible connectivity options, making it an ideal choice for a wide range of applications. Whether for professional use in a corporate environment or for creative displays in retail, the C3215 consistently delivers exceptional performance and reliability.