Planar C3215 user manual Problems and Suggestions, What happens What to do

Page 51

Problems and Suggestions

Contact your service representative if the suggested actions do not solve the problem.

What happens

What to do

Application software problems

Make sure all cables are installed correctly.

 

Verify that your system hardware configuration

 

is set correctly. In Setup, check the values

 

against the system settings you recorded

 

previously. If an error is evident (for example,

 

the wrong type of drive is specified), make the

 

change in Setup and reboot the system. Record

 

your change.

 

Make sure the software is properly configured

 

for the system. Refer to the software documen-

 

tation for information.

 

Try a different copy of the software to see if

 

the problem is with the copy you are using.

 

If other software runs correctly on the system,

 

contact the vendor of the software that fails.

 

If you check all of the above with no success,

 

try clearing CMOS RAM and reconfiguring

 

the system. Make sure you have your list of

 

system settings available to re-enter, as clearing

 

CMOS RAM sets the options to their default

 

values.

Characters on the screen are distorted

Make sure the brightness and contrast controls

or incorrect

are properly adjusted.

 

Make sure the correct display drivers have

 

been loaded.

 

Make sure the display resolution is set correctly

 

to the product you’ve purchased.

Characters do not appear on screen

Reboot the system. Cycle the power.

CMOS RAM settings are wrong

If system settings stored in CMOS RAM

 

change for no apparent reason (for example,

 

the time of day develops an error), the backup

 

battery may no longer have enough power to

 

maintain the settings. Replace the battery.

 

 

Diskette drive light does not go on

Make sure the power and signal cables for the

when drive is in use or is tested by POST

drive are properly installed.

 

Check that the drive is properly configured and

 

enabled in Setup.

Hard drive light does not go on when drive is in use or is tested by POST

Check that the drive is properly configured and enabled in Setup.

40Planar Clean Screen II PC User’s Manual

Page 50 Page 52
Image 51
Page 50 Page 52
Contents User’s Manual Integrated Computer with LCD Color Display USER’S ManualIi Planar Clean Screen II PC User’s Manual Commencement of Warranty Federal Communications Commission FCC RequirementsCanadian Emissions Requirements Installation Duration of WarrantyPlace of Repair or Replacement Limitation of WarrantyTable of Contents Vi Planar Clean Screen II Screen PC User’s Manual Reference Guide ViiWhat if I’m missing something? Before You BeginWhat’s in the box? What’s in this manual?Clean Screen II Mounts and Accessories Safety InstructionsConnections Bottom Front PanelChapter Four System Setup Chapter One The Installation ExpressChapter Two The Clean Screen II PC Clean Screen II FactsWelcome Chapter Two The Clean Screen II PC Inside Back HousingChapter Two The Clean Screen II PC Removing the Back Housing Chapter Three Hardware Installation and ReplacementInstalling Memory To install a memory moduleTo remove a memory module Range CPU address Region Cached Memory MapInstalling the new hard disk Replacing the Hard Disk DriveRemoving the existing hard disk Flash memory. See Chapter Five Bios Setup Replacing the BatteryReplacing the Fuse Mounting the Clean Screen PC Card Slot Chapter Four System SetupConnecting the Keyboard Connecting PeripheralsUSB Connection Power SupplyPower Cord Selection Floppy Drive ConnectionDriver Overview Powering Up the Clean Screen II PCPower On Setup F2Chapter Five Bios Setup Entering the Bios Setup ProgramSetup Screens Main Menu Extended Memory Boot Options Sub-MenuBoot-Time Diagnostic Screen System MemoryMulti-Sector Transfers Primary Master/Slave Sub-Menus under Main MenuAutotype Fixed Disk TypeBit I/O LBA Mode ControlTransfer Mode Ultra DMA ModeBoot Options Sub-Menu under Main Menu Large Disk Access Mode Device Configuration Sub-MenuInstalled OS Win Reset Configuration DataPCI Configuration Sub-Menu PS2 MouseLegacy USB Support Device Configuration Sub-Menu under Advanced Menu Floppy Disk Controller Standby Timeout Power Management MenuPower Savings Idle ModeResume On Time Resume TimeIDE Monitoring Removable Format Boot MenuHard Drive Removable DevicesExit Menu Approved cleaning solutions include Chapter Six Care and CleaningMaintenance Tips Cleaning TipsAppendix a Product Specifications Optional Resistive Touch Screen Controller External Serial PortsUSB Ports Floppy Disk Drive PortDescription Pin Environmental SpecificationsAppendix B Programming Interface Assigned and Available IRQsDMAs Address Device Address ListAppendix C Troubleshooting Troubleshooting ProcedureAnti-Virus Alert Causes Boot FailuresProblems After the System Has Been Running Correctly Problems At Initial System StartupProblems Running New Application Software Problems Operating PC CardsProblems with Ethernet What happens What to do Problems and SuggestionsSee Problems at Initial System Start-up Error Message / Beeps Explanation Error and Information MessagesPost Error Message ExplanationMessage Explanation PCI Configuration Status and Error MessagesResetting the System Appendix D Touch Screen optional Cmos ConfigurationFor Service For Further Information and Driver UpdatesAppendix E Technical Support Planar Clean Screen II PC User’s Manual Canada

C3215 specifications

The Planar C3215 is a high-performance display solution designed for a variety of professional and commercial applications. With its sleek design and advanced functionalities, the C3215 stands out as an ideal choice for environments ranging from corporate settings to retail spaces.

One of the primary features of the Planar C3215 is its impressive display quality. The monitor boasts a resolution of 1920x1080 pixels, providing vibrant colors and sharp images that enhance the viewing experience. The LED-backlit technology further improves brightness and energy efficiency, ensuring that users benefit from striking visuals while minimizing power consumption.

The C3215 display is equipped with a wide viewing angle, utilizing in-plane switching (IPS) technology that allows for consistent color accuracy and clarity from various angles. This feature makes it particularly suitable for collaborative workspaces or public displays, where multiple viewers may be observing the screen simultaneously from different positions.

In terms of connectivity, the C3215 is versatile. It offers multiple input options, including HDMI, DisplayPort, and VGA, allowing seamless integration with a variety of devices such as computers, laptops, and media players. This flexibility ensures that users can easily switch between different sources without hassle.

Durability is another key aspect of the C3215. The screen is designed for continuous usage, making it suitable for 24/7 operation in demanding environments. Its robust construction means it can withstand the rigors of daily use, ensuring longevity and reliability.

Moreover, the Planar C3215 incorporates advanced anti-glare technology, reducing reflections and providing users with a clearer view of the content, even in brightly lit settings. This characteristic is essential for environments where lighting conditions can be unpredictable.

For those concerned about installation, the C3215 is designed with user convenience in mind. It supports multiple mounting options, including VESA mounting, which allows users to easily mount the display on walls or use it in conjunction with various stand solutions.

In summary, the Planar C3215 is a feature-rich display that combines superb image quality, durability, and flexible connectivity options, making it an ideal choice for a wide range of applications. Whether for professional use in a corporate environment or for creative displays in retail, the C3215 consistently delivers exceptional performance and reliability.
Top Page Image Contents