Planar C3i/EX manual Dome E3 Specification

Page 43

Dome E3 Specification

In locations where 240V outlets are used, connect the Dome E3 display to only a center- tapped, 240V, single-phase supply (only for Canada and the United States).

Category	Characteristic Item	Specification

Screen	Screen size diagonal	528 mm (20.8 in.)
	Resolution	1536 x 2048 pixels (portrait)
		2048 x 1536 pixels (landscape)
	Pixel pitch	0.207 mm, 123 ppi
	Pixel arrangement	Subpixel vertical stripe
	Active area (mm)	423.9 (H) x 318.0 (V)
	Color supported	256 shades of gray, programmable gamma from
		palette of up to 3061 shades
	Refresh rate	60 Hz
	Contrast ratio	700:1 (typical)
	Brightness	800 cd/m2 (typical)
	Pixel rise/fall time	35 ms
	Viewing angle	170° (± 85°) horizontal/vertical

Interface	Digital Video In	DVI Rev. 1.0 single- or dual-channel digital connector
	Display control - brightness	DDC2B+
	Display identification	EDID read using DDC2B+
	USB hub	Universal Serial Bus (USB) Rev. 1.1:
		1 uplink B port; 2 downlink A ports
	Display status	Dual-stack tricolor LEDs on back panel

Input formats	Landscape orientation	2048 x 1536 (8- bit per pixel)
	Portrait orientation	1536 x 2048 (8-bit per pixel)
	Screen type	AMLCD (active-matrix liquid crystal display)

Physical	Display size (without stand)	475 mm x 368 mm x 96 mm
		(18.7 in. x 14.5 in. x 4.0 in.)
	Display weight (without stand)	6.35 kg (<15 lb)
	Mounting options	Desktop stand with integrated USB (standard);
		100-mm VESA mounting (optional)

Power	Adapter	Ault MW122KA1223F52 (CAUTION: Use only the
		power adapter supplied with the display unit.)

Dome E3 Specification 33

Image 43

Contents

User’s Guide 020-0377-01A Contents Product Information Intended use Symbol explanationsSafety tips Safety precautionsPreventing fire and injury Unpacking and handling tipsCleaning the display Disposal information Shipping/storing the displayDVI cable System Requirements About the DisplayDisplay Components Tilt range Height range Display PositionsStand cable cover Desk Stand FeaturesMoving from Dome C3i to Dome EX Display System Installing the DisplayTo set landscape mode as default display mode Set the DIP Switch on the Dome DX2 BoardTo disable VGA To enable EpromTo install the display controller Install the Display ControllerTo connect the cables Connect the Video and Power CablesInstallation preparation Install Dome DX2 Driver and Dome CXtra SoftwareRequired Sun software packages To install the driver and Dome CXtra Installing the Display Configure Display Settings To edit the OWconfig file Overriding the default display modeDome Display To modify the OWconfig file Using visual classes To emulate a PseudoColor visual class To check the default visualSunallplanes Shape MIT-SHM Look Default visual id For visual Dome Display Configuring the Common Desktop Environment Configure the Window EnvironmentRunning OpenWindow from the console To use a Dome device with a Sun console To use one or more Dome devicesScreen saver tips Dpms Screen SaverTo set the Dpms Screen Saver Console Modification To use the setenv commandDome CXtra Software Appendix Problem Possible Cause Solution Troubleshooting Category Characteristic Item Specification Dome C3i SpecificationReliability Power SupplyEnvironment Dome E2 Specification Power Supply Dome E3 Specification EMI shielding No emission of low-level radiation Temperature Dome E3c Specification Display Mtbf 30,000 hours Backlight Dome E5 Specification Display Mtbf 50,000 hours Backlight 2560 x Video ModesDetails of DIN connectors Connector PortsLED Status Lights Power-up sequence information from LED Index 21-22 Canada, European Union, United States Regulatory CompliancePage Fax + 358 9 420 EU Declaration of Conformity for Medical Application FCC Compliance Statement Korea AustralianChina JapanStandard Warranty Return Procedure Standard WarrantySummary Limitation of Implied Warranties Summary Limitations and Exclusions of Dome DisplaysEffect of Local Law Exclusion of DamagesMedicalsales@planar.com Medicalsupport@planar.com