Planar PD8150, PD8130 operation manual Operation

Page 72

Operation

4:3 causes the port to output 12 volts whenever the 4:3 aspect ratio is chosen. The output stops if PIP is enabled (PIP source is set to anything other than off).

4:3 Narrow causes the port to output 12 volts whenever the 4:3 Narrow aspect ratio is chosen. The output stops if PIP is enabled (that is, the PIP source is set to anything other than off).

RS232 causes the port to output 12 volts when an RS232 screen trigger 1 “on” command is received and stop when a trigger 1 “off” command is received. The 12 volt output also stops when the projector is turned off.

Trigger 2 (PD8150 only): Select Trigger 2 from the Control menu to configure the Trigger 2 output. Trigger 2 operates identically to Trigger 1.

Remote Code Set: Select Remote Code Set from the Control menu to specify the remote IR code set to which the PD8130/PD8150 responds. The default is Set-1. Choose Set-2if other equipment in the theater responds to commands from the PD8130/PD8150 remote control in ways that are unexpected or undesirable.

When you select a different remote code set on the PD8130/PD8150, you must re-program the remote control unit to use that same code set. To do this, press and hold the LIGHT and ENTER buttons simultaneously for approximately five seconds. When the code set has changed, the remote control back-lighting “blinks” to visually confirm the change.

Table 6-1lists the IR codes associated with each remote control button.

Auto Source: This control chooses whether or not to scan for other active sources if the current source is not available. The default setting is Off.

58

Planar PD8130/PD8150 Installation/Operation Manual

Image 72
Contents PD8130 PD8150 Home Theater Projector Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Maintenance and Troubleshooting OperationSpecifications Table of Contents Xii List Of Figures List Of Figures Xiv Introduction About This ManualTarget Audience Using This Manual If you need Turn toDescription, Features and Benefits Additional Features of the PD8150Key Features and Benefits Parts List Optional AccessoriesControls and Functions PD8130/PD8150 at a GlanceCursor Keys Exhaust Vent PD8130/PD8150 Rear/Bottom/Top View Rear Cover Power Input 100 to 240 VAC Component 1/SCART RCA connectorsPD8130/PD8150 Rear Panel RGBTrigger 2 3.5-mm, mini phono jack PD8150 only RS-232PD8130/PD8150 Remote Control OFFSource Selection Buttons Memory Preset Buttons M1 / M2 / M3 Picture Adjustment Buttons ContrastAspect Ratio Selection Button BrightnessInstallation Remote ControlOperation IR Reception Angles Quick Setup Installation OverviewStep Procedure For Details, Refer to Installation Projector Installation OptionsInstallation Type ConsiderationsAmbient Light Throw DistanceEstimating Throw Distance Vertical and Horizontal PositionVertical Lens Shift Horizontal Lens Shift Example Only Vertical lens shift figures are for ceiling mountFolded Optics Folded OpticsMounting the PD8130/PD8150 Connector Panel Access Connections to the PD8130/PD8150Connecting Source Components to the PD8130/PD8150 HDMI/DVI Connections See FigureRGB Connections Component Video Connections 10. Composite and S-Video Connections RS-232 Controller ConnectionCommunications on Connecting 12-Volt Connecting an External IRTrigger Output to External Theater EquipmentTurning on the Power Changing the OSD Language Connecting to AC PowerAdjusting the Picture Lens AdjustmentsOrientation Installation Installation Operation Selecting Video MemorySelecting an Aspect Ratio Selecting An Input SourceUsing Picture-In-Picture PIP Available Main and PIP Source CombinationsPIP Input Source MainUsing the On-Screen Menus Service MainAdvanced SystemPD8130/PD8150 Main Menu Aspect Ratio Settings Aspect Geometry of Projected Image169 Letterbox 1080i Hdtv Image You must enter a passcode to access the Save ISF Sub-menuTypical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Crop Overscan ExamplesSource Select Sub-Menu Advanced PD8130/PD8150 Advanced MenuOperation X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Adjust the Phase after adjusting Tracking see below. If System 11. PD8130/PD8150 System Menu12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Operation Language Service 15. PD8130/PD8150 Service MenuOperation OSD menus are not available when in test pattern Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Light and EnterLED is flashing red Maintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname SetGam.brig Operations Commands Operations Control Commands Function Action on unitSerial Commands ValuesSave.isf Source.sel = ? Bcolor = ? Auto.pow.off = ? M1.key = ? Act.source Language = ? Specifications PD8130/PD8150 SpecificationsPD8130/PD8150 Specifications Native Resolution PerformanceMicrodisplay Aspect RatiosDimensions Weight without lensOperating Temperature Universal Power SupplyPD8130/PD8150 Dimensions PD8130/PD8150 DimensionsSupported Signal Timings by Input Supported TimingsPAL-B/G Page Part No -0858-00 rev. a January