Planar PD8130, PD8150 operation manual Maintenance and Troubleshooting, Lamp Replacement

Page 77

Maintenance and Troubleshooting

Maintenance and Troubleshooting

The lamp should be replaced when it reaches the end of its life (typically between 2000 and 4000 hours depending on the Lamp Power setting), or sooner if a noticeable degradation in brightness occurs. Contact your Planar dealer to obtain a replacement lamp.

1.Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 60 minutes prior to removing the lamp assembly for replacement.

2. Using a flat-blade screwdriver, loosen the two screws holding the rear compartment cover in place.

5.1

Lamp Replacement

￿￿

3. Remove the rear compartment cover by tilting it upward.

4.Loosen the screw on the lamp cover and pull the lamp cover out.

5.Loosen the two screws on the lamp module.

6.Pull the lamp module handle firmly to remove the lamp module.

7.Perform Steps 6 through 2 (in reverse order) to install the new lamp module.

8.Turn on the power and reset the lamp timer.

￿

￿

￿

￿￿

Planar PD8130/PD8150 Installation/Operation Manual

63

Image 77
Contents PD8130 PD8150 Home Theater Projector Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Operation Maintenance and TroubleshootingSpecifications Table of Contents Xii List Of Figures List Of Figures Xiv Target Audience IntroductionAbout This Manual If you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsAdditional Features of the PD8150 Optional Accessories Parts ListCursor Keys Controls and FunctionsPD8130/PD8150 at a Glance Exhaust Vent PD8130/PD8150 Rear/Bottom/Top View Rear Cover Component 1/SCART RCA connectors Power Input 100 to 240 VACPD8130/PD8150 Rear Panel RGBRS-232 Trigger 2 3.5-mm, mini phono jack PD8150 onlySource Selection Buttons PD8130/PD8150 Remote ControlOFF Picture Adjustment Buttons Contrast Memory Preset Buttons M1 / M2 / M3Aspect Ratio Selection Button BrightnessOperation InstallationRemote Control IR Reception Angles Step Procedure For Details, Refer to Quick SetupInstallation Overview Projector Installation Options InstallationInstallation Type ConsiderationsEstimating Throw Distance Ambient LightThrow Distance Vertical Lens Shift Vertical and HorizontalPosition Vertical lens shift figures are for ceiling mount Horizontal Lens Shift Example OnlyFolded Optics Folded OpticsMounting the PD8130/PD8150 Connections to the PD8130/PD8150 Connector Panel AccessHDMI/DVI Connections See Figure Connecting Source Components to the PD8130/PD8150RGB Connections Component Video Connections 10. Composite and S-Video Connections Communications on RS-232 ControllerConnection Connecting an External IR Connecting 12-VoltTrigger Output to External Theater EquipmentConnecting to AC Power Turning on the Power Changing the OSD LanguageOrientation Adjusting the PictureLens Adjustments Installation Installation Selecting Video Memory OperationSelecting an Aspect Ratio Selecting An Input SourceAvailable Main and PIP Source Combinations Using Picture-In-Picture PIPPIP Input Source MainUsing the On-Screen Menus Main ServiceAdvanced SystemPD8130/PD8150 Main Menu 169 Aspect Ratio SettingsAspect Geometry of Projected Image Letterbox 1080i Hdtv Image Sub-menu You must enter a passcode to access the Save ISFTypical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples CropSource Select Sub-Menu PD8130/PD8150 Advanced Menu AdvancedOperation Color X/y Color Gamut ValuesRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Adjust the Phase after adjusting Tracking see below. If 11. PD8130/PD8150 System Menu System12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Operation Language 15. PD8130/PD8150 Service Menu ServiceOperation OSD menus are not available when in test pattern Lamp Replacement Maintenance and TroubleshootingTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Light and EnterLED is flashing red Maintenance and Troubleshooting Serial Communications Key CommandsRS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR CodesGam.brig Operations Control Commands Function Action on unit Operations CommandsValues Serial CommandsSave.isf Source.sel = ? Bcolor = ? Auto.pow.off = ? M1.key = ? Act.source Language = ? PD8130/PD8150 Specifications SpecificationsPD8130/PD8150 Specifications Performance Native ResolutionMicrodisplay Aspect RatiosWeight without lens DimensionsOperating Temperature Universal Power SupplyPD8130/PD8150 Dimensions PD8130/PD8150 DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G Page Part No -0858-00 rev. a January