Planar PD8150, PD8130 operation manual Vertical and Horizontal, Position, Vertical Lens Shift

Page 32

Installation

Vertical and Horizontal

Proper placement of the projector relative to the screen will yield a rectangular,

Position

 

perfectly-centered image that completely fills the screen.

 

 

Ideally, the projector should be positioned perpendicular to the screen and in

 

 

such a way that the lens center is aligned with either the top or bottom edge of

 

 

the screen area, and centered horizontally. See Figure 3-3.

Ceiling Installation

 

Ceiling

Height

Projection Distance

 

x

 

Lens Center

Lens Center

Screen

Floor Installation

HeightScreen

Lens Center

x

Lens Center

Projection Distance

Floor

 

Figure 3-3. Projector Placement

Vertical Lens Shift

You can use the lens shift controls on the projector to center the image on the

 

screen. Lens shift is generally expressed as a percentage of the screen height or

 

width, as shown in Figure 3-4and Figure 3-5.

Screen Center

0%

50% Height

Lens Shift

(0.5 x H)

100% Height

Lens Shift

(1.0 x H)

Note: This is a general example of lens shift. Lenses vary in their shift

capabilities. No particular lens or projector is used in this example.

Figure 3-4. Vertical Lens Shift (Example Only)

18

Planar PD8130/PD8150 Installation/Operation Manual

Image 32
Contents PD8130 PD8150 Home Theater Projector Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Maintenance and Troubleshooting OperationSpecifications Table of Contents Xii List Of Figures List Of Figures Xiv Target Audience IntroductionAbout This Manual Using This Manual If you need Turn toKey Features and Benefits Description, Features and BenefitsAdditional Features of the PD8150 Parts List Optional AccessoriesCursor Keys Controls and FunctionsPD8130/PD8150 at a Glance Exhaust Vent PD8130/PD8150 Rear/Bottom/Top View Rear Cover Power Input 100 to 240 VAC Component 1/SCART RCA connectorsPD8130/PD8150 Rear Panel RGBTrigger 2 3.5-mm, mini phono jack PD8150 only RS-232Source Selection Buttons PD8130/PD8150 Remote ControlOFF Memory Preset Buttons M1 / M2 / M3 Picture Adjustment Buttons ContrastAspect Ratio Selection Button BrightnessOperation InstallationRemote Control IR Reception Angles Step Procedure For Details, Refer to Quick SetupInstallation Overview Installation Projector Installation OptionsInstallation Type ConsiderationsEstimating Throw Distance Ambient LightThrow Distance Vertical Lens Shift Vertical and HorizontalPosition Horizontal Lens Shift Example Only Vertical lens shift figures are for ceiling mountFolded Optics Folded OpticsMounting the PD8130/PD8150 Connector Panel Access Connections to the PD8130/PD8150Connecting Source Components to the PD8130/PD8150 HDMI/DVI Connections See FigureRGB Connections Component Video Connections 10. Composite and S-Video Connections Communications on RS-232 ControllerConnection Connecting 12-Volt Connecting an External IRTrigger Output to External Theater EquipmentTurning on the Power Changing the OSD Language Connecting to AC PowerOrientation Adjusting the PictureLens Adjustments Installation Installation Operation Selecting Video MemorySelecting an Aspect Ratio Selecting An Input SourceUsing Picture-In-Picture PIP Available Main and PIP Source CombinationsPIP Input Source MainUsing the On-Screen Menus Service MainAdvanced SystemPD8130/PD8150 Main Menu 169 Aspect Ratio SettingsAspect Geometry of Projected Image Letterbox 1080i Hdtv Image You must enter a passcode to access the Save ISF Sub-menuTypical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Crop Overscan ExamplesSource Select Sub-Menu Advanced PD8130/PD8150 Advanced MenuOperation X/y Color Gamut Values ColorRGB Adjust Sub-Menu 10. Fine Sync Sub-Menu Adjust the Phase after adjusting Tracking see below. If System 11. PD8130/PD8150 System Menu12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Control Operation Language Service 15. PD8130/PD8150 Service MenuOperation OSD menus are not available when in test pattern Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Light and EnterLED is flashing red Maintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname SetGam.brig Operations Commands Operations Control Commands Function Action on unitSerial Commands ValuesSave.isf Source.sel = ? Bcolor = ? Auto.pow.off = ? M1.key = ? Act.source Language = ? PD8130/PD8150 Specifications SpecificationsPD8130/PD8150 Specifications Native Resolution PerformanceMicrodisplay Aspect RatiosDimensions Weight without lensOperating Temperature Universal Power SupplyPD8130/PD8150 Dimensions PD8130/PD8150 DimensionsSupported Signal Timings by Input Supported TimingsPAL-B/G Page Part No -0858-00 rev. a January