Onkyo TX-SA706 Remote Control, Phono, Component Video in 1, Hdmi in 1-4 and OUT, Monitor OUT

Front & Rear Panels—Continued

au REMOTE CONTROL

This u(Remote Interactive) jack can be con- nected to an ujack on another Onkyo AV compo- nent. The AV receiver/AV amplifier’s remote controller can then be used to control that compo- nent. To use u, you must make an analog audio connection (RCA) between the AV receiver/AV amplifier and the other AV component, even if they are connected digitally.

bPHONO IN

This audio input is for connecting a turntable.

cCOMPONENT VIDEO IN 1 and 2

These RCA component video inputs are for con- necting components with a component video out- put, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Component Video Setup” on page 43.

COMPONENT VIDEO MONITOR OUT

This RCA component video output is for connect- ing a TV or projector with a component video input.

dHDMI IN 1–4 and OUT

HDMI (High Definition Multimedia Interface) con- nections carry digital audio and digital video.

The HDMI inputs are for connecting components with an HDMI output, such as a DVD player, DVD recorder, or DVR (digital video recorder). They’re assignable, which means you can assign each one to an input selector to suit your setup. See “HDMI Input Setup” on page 42.

The HDMI output is for connecting a TV or projec- tor with an HDMI input.

eMONITOR OUT

The S-Video or composite video jack should be connected to a video input on your TV or projector.

fIR IN

A commercially available IR receiver can be con- nected to the IR IN jack, allowing you to control the AV receiver/AV amplifier while you’re in Zone 2, or control it when it’s out of sight, for example, installed in a cabinet.

g12V TRIGGER OUT ZONE 2

This output can be connected to the 12-volt trigger input on a component in Zone 2. When Zone 2 is turned on on the AV receiver/AV amplifier, a 12- volt trigger signal is output.

hFM ANTENNA (TX-SR706 only)

This jack is for connecting an FM antenna.

iAM ANTENNA (TX-SR706 only)

These push terminals are for connecting an AM antenna.

jRS232

This is the RS232 port.

kXM antenna (North American models only)

This jack is for connecting an XM Mini-Tuner and Home Dock, sold separately (see the separate XM instructions).

lSIRIUS antenna (North American models only)

This jack is for connecting a SIRIUS Satellite Radio antenna, sold separately (see the separate SIRIUS instructions).

mAC INLET (not North American models)

The supplied power cord is connected here. The other end of the power cord should be connected to a suitable wall outlet.

nDIGITAL COAXIAL IN 1, 2, and 3

These coaxial digital audio inputs are for connect- ing components with coaxial digital audio outputs, such as CD and DVD players. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” on page 44.

oDIGITAL OPTICAL IN 1 and 2

These optical digital audio inputs are for connecting components with optical digital audio outputs, such as CD and DVD players. They’re assignable, which means you can assign each one to an input selector to suit your setup. See “Digital Input Setup” on page 44.

pGND screw

This screw is for connecting a turntable’s ground wire.

qTUNER IN (TX-SA706 only)

This analog audio input is for connecting a tuner’s analog audio output.

rCD IN

This analog audio input is for connecting a CD player’s analog audio output.

sTAPE IN/OUT

This analog audio input and output are for connect- ing a recorder with an analog audio input and output (cassette, Mini Disc, etc.).

tGAME/TV IN

Here you can connect a game console, TV, etc. Input jacks include S-Video, composite video, and analog audio.

uCBL/SAT IN

Here you can connect a cable/satellite receiver, set- top box, etc. Input jacks include S-Video, composite video, and analog audio.

12