Optoma Technology TW6313D appendix Installing the Batteries, EN-13

Page 13
Installing the Batteries

Installing the Batteries

1.Open the battery cover in the direction shown.

2.Install batteries as indicated by the diagram inside the compartment.

3.Close the battery cover into position.

Caution

„Risk of explosion if battery is replaced by an incorrect type. „Dispose of used batteries according to the instructions.

„Make sure the plus and minus terminals are correctly aligned when loading a battery.

Note

„Keep the batteries out of the reach of children. There is a danger of death by accidentally swallowing the batteries.

„Remove batteries from remote control when not using for extended periods.

„Do not dispose of the used batteries along with household waste. Dispose of used batteries according to local regulations.

„Danger of explosion may happen if batteries are incorrectly replaced. Replce all the batteries with new ones.

„Batteries should not be in or near to fire or water, keep batteries in a dark, cool and dry place.

„If suspect battery leakage, wipe out the leakage and then replace new batteries. If the leakage adheres to your body or clothes, rinse well with water immediately.

EN-13

Image 13
Contents Using the Product CONTENTSConnecting Video source devices Adjusting the Projector Zoom and FocusUsage Notice Safety InstructionsEN-3 EN-4 Notes on the AC Power CordIntroduction Projector FeaturesPackage Contents Front View Projector Overview9 8 7 Bottom View Rear ViewEN-8 Control Panel Using the Product1 2 3 4 5 Connection Ports Remote Control 15 Re-SYNC 16 Volume+Page AV muteEN-13 Installing the BatteriesEN-14 Remote Control OperationEN-15 ConnectionConnecting a computer Connecting a computer or monitorConnecting a monitor EN-17 Connecting Video source devicesConnecting a Component Video source device Connecting an HDMI source deviceTo connect the projector to an HDMI source device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceEN-19 To connect the projector to a composite Video source device Connecting a composite Video source deviceEN-20 Powering On the Projector Powering On/Off the ProjectorPowering Off the Projector OperationAdjusting the Projector Zoom and Focus Adjusting the Projector HeightEN-22 XGA model Adjusting Projection Image SizeWXGA model EN-23Menu Operation How to operateEN-25 Color Settings ImageBrightness ContrastThere are many factory presets optimized for various types of images Phase SignalFrequency H Position Horizontal PositionSound Video ImageVolume ColorLamp Time Reset SettingMenu Position ProjectionPower mode standby 3D Mode Wireless3D Sync Invert EN-32Language Factory DefaultEN-33 EN-34 Use web browser to control your projectorCategory EN-35Input-Length characters EN-36 Connect you computer to the projector5. Click Use the following IP address, and type in as below „ Default gateway10.0.50.254„ IP address10.0.50.101 „ Subnet mask255.0.0.0 EN-37EN-38 Crestron RoomView Control ToolEN-39 2. Edit Room 3. Edit AttributeEN-40 4. Edit EventReplacing the Lamp AppendixEN-42 EN-43 Ceiling mount installationComputer Compatibility ModesEN-45 EN-46 VideoRS232 Pin Assignments RS232 Commands and Protocol Function ListEN-48 RS232 Protocol Function ListEN-49 XGA n 0/1/2/3/4 = 43/169-I/169-II/Native/AUTO EN-50Start-up problems TroubleshootingImage problems Remote control problemsPOWER LED Indicator MessagesProjector Status TEMPCanada Optoma Global OfficesEurope FranceLatin America ScandinaviaKorea Japan+86-21-62947376 上海市长宁区凯旋路 1205 号 5 楼 +86-21-62947375FCC Notice Regulation & Safety NoticesNotice Shielded cables Notice Canadian users Operation conditionsDeclaration of Conformity for EU countries Disposal instructions1 Switch 14 Enter