Optoma Technology TW6313D appendix Connecting a composite Video source device, EN-20

Page 20

Connecting a composite Video source device

Examine your Video source device to determine if it has a set of unused composite Video output sockets available:

If so, you can continue with this procedure.

If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a composite Video source device:

1.Take a Video cable and connect one end to the composite Video output socket of the Video source device.

2.Connect the other end of the Video cable to the VIDEO socket on the projector.

Important

If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

You need only connect to this device using a composite Video connection if Component Video and S-Video inputs are unavailable for use. See “Connecting Video source devices” on page 17 for details.

EN-20

Image 20

Contents CONTENTS Using the ProductConnecting Video source devices Adjusting the Projector Zoom and FocusSafety Instructions Usage NoticeEN-3 Notes on the AC Power Cord EN-4Projector Features IntroductionPackage Contents 9 8 7 Projector OverviewFront View EN-8 Rear ViewBottom View 1 2 3 4 5 Using the ProductControl Panel Connection Ports Remote Control 16 Volume+ 15 Re-SYNCPage AV muteInstalling the Batteries EN-13Remote Control Operation EN-14Connection EN-15Connecting a monitor Connecting a computer or monitorConnecting a computer Connecting Video source devices EN-17Connecting an HDMI source device Connecting a Component Video source deviceTo connect the projector to an HDMI source device To connect the projector to a Component Video source deviceEN-19 Connecting an S-Video source deviceTo connect the projector to an S-Video source device EN-20 Connecting a composite Video source deviceTo connect the projector to a composite Video source device Powering On/Off the Projector Powering On the ProjectorPowering Off the Projector OperationEN-22 Adjusting the Projector HeightAdjusting the Projector Zoom and Focus Adjusting Projection Image Size XGA modelWXGA model EN-23How to operate Menu OperationEN-25 Image Color SettingsBrightness ContrastThere are many factory presets optimized for various types of images Signal PhaseFrequency H Position Horizontal PositionVideo Image SoundVolume ColorSetting Lamp Time ResetMenu Position ProjectionPower mode standby Wireless 3D Mode3D Sync Invert EN-32EN-33 Factory DefaultLanguage Use web browser to control your projector EN-34Input-Length characters EN-35Category Connect you computer to the projector EN-36„ Default gateway10.0.50.254 5. Click Use the following IP address, and type in as below„ IP address10.0.50.101 „ Subnet mask255.0.0.0 EN-37Crestron RoomView Control Tool EN-382. Edit Room 3. Edit Attribute EN-394. Edit Event EN-40Appendix Replacing the LampEN-42 Ceiling mount installation EN-43Compatibility Modes ComputerEN-45 Video EN-46RS232 Commands and Protocol Function List RS232 Pin AssignmentsRS232 Protocol Function List EN-48EN-49 EN-50 XGA n 0/1/2/3/4 = 43/169-I/169-II/Native/AUTOTroubleshooting Start-up problemsImage problems Remote control problemsLED Indicator Messages POWERProjector Status TEMPOptoma Global Offices CanadaEurope FranceScandinavia Latin AmericaKorea Japan上海市长宁区 +86-21-62947376凯旋路 1205 号 5 楼 +86-21-62947375Notice Shielded cables Regulation & Safety NoticesFCC Notice Operation conditions Notice Canadian usersDeclaration of Conformity for EU countries Disposal instructions1 Switch 14 Enter