Optoma Technology TW6313D appendix Connecting Video source devices, EN-17

Page 17

Connecting Video source devices

Connecting Video source devices

You can connect your projector to various Video source devices that provide any one of the following output sockets:

HDMI

Component Video

S-Video

Video (composite)

You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the avail- ability of matching terminals on both the projector and the Video source device as described below:

Terminal name	Terminal appearance	Reference	Picture quality
HDMI	HDMI	“Connecting an	Best
		HDMI source
		device” on
		page 18	Better
Component	VGA1-IN/YPbPr or	“Connecting a	Better
Video	VGA2-IN/YPbPrComponent Video
		source device” on
		page 18	Good
S-Video	S-VIDEO	“Connecting an	Good
		S-Video source
		device” on
		page 19	Normal
Video	VIDEO	“Connecting a	Normal
		composite Video
		source device” on
		page 20

Note

Not all models have HDMI input jack, please check your projector before connecting

EN-17

Image 17

Contents Using the Product CONTENTSConnecting Video source devices Adjusting the Projector Zoom and FocusUsage Notice Safety InstructionsEN-3 EN-4 Notes on the AC Power CordIntroduction Projector FeaturesPackage Contents 9 8 7 Projector OverviewFront View EN-8 Rear ViewBottom View 1 2 3 4 5 Using the ProductControl Panel Connection Ports Remote Control 15 Re-SYNC 16 Volume+Page AV muteEN-13 Installing the BatteriesEN-14 Remote Control OperationEN-15 ConnectionConnecting a monitor Connecting a computer or monitorConnecting a computer EN-17 Connecting Video source devicesConnecting a Component Video source device Connecting an HDMI source deviceTo connect the projector to an HDMI source device To connect the projector to a Component Video source deviceEN-19 Connecting an S-Video source deviceTo connect the projector to an S-Video source device EN-20 Connecting a composite Video source deviceTo connect the projector to a composite Video source device Powering On the Projector Powering On/Off the ProjectorPowering Off the Projector OperationEN-22 Adjusting the Projector HeightAdjusting the Projector Zoom and Focus XGA model Adjusting Projection Image SizeWXGA model EN-23Menu Operation How to operateEN-25 Color Settings ImageBrightness ContrastThere are many factory presets optimized for various types of images Phase SignalFrequency H Position Horizontal PositionSound Video ImageVolume ColorLamp Time Reset SettingMenu Position ProjectionPower mode standby 3D Mode Wireless3D Sync Invert EN-32EN-33 Factory DefaultLanguage EN-34 Use web browser to control your projectorInput-Length characters EN-35Category EN-36 Connect you computer to the projector5. Click Use the following IP address, and type in as below „ Default gateway10.0.50.254„ IP address10.0.50.101 „ Subnet mask255.0.0.0 EN-37EN-38 Crestron RoomView Control ToolEN-39 2. Edit Room 3. Edit AttributeEN-40 4. Edit EventReplacing the Lamp AppendixEN-42 EN-43 Ceiling mount installationComputer Compatibility ModesEN-45 EN-46 VideoRS232 Pin Assignments RS232 Commands and Protocol Function ListEN-48 RS232 Protocol Function ListEN-49 XGA n 0/1/2/3/4 = 43/169-I/169-II/Native/AUTO EN-50Start-up problems TroubleshootingImage problems Remote control problemsPOWER LED Indicator MessagesProjector Status TEMPCanada Optoma Global OfficesEurope FranceLatin America ScandinaviaKorea Japan+86-21-62947376 上海市长宁区凯旋路 1205 号 5 楼 +86-21-62947375Notice Shielded cables Regulation & Safety NoticesFCC Notice Notice Canadian users Operation conditionsDeclaration of Conformity for EU countries Disposal instructions1 Switch 14 Enter