InFocus P1501 manual Declaration of Conformity, Trademarks, FCC Warning, Canada, Agency Approvals

Page 2

Declaration of Conformity

Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland, Oregon 97223-8368 USA

We declare under our sole responsibility that this projector conforms to the following directives and norms:

EuP Directive 2005/32/EC EMC Directive 2004/108/EC EMC: EN 55022

EN 55024 EN 61000-3-2 EN 61000-3-3

Low Voltage Directive 2006/95/EC Safety: IEC 60950-1: 2005 (MOD)

Trademarks

DisplayLink is a trademark of DisplayLink Corporation.

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated. DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.

Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency Approvals

cTUVus

Other specific Country Approvals may apply. Please see product certification label. This document applies to regulatory models P1501 and P1503.

Input ratings: 100-240Vac, 2.9A, 50-60Hz

InFocus reserves the right to alter product offerings and specifications at any time without notice.

1

Page 1 Page 3
Image 2
Page 1 Page 3
Contents 009-1313-02 DISPERINDAG No. 0287/1.824.51/09.03 IN1501, IN1503Regulatory models P1501, P1503 FCC Warning Declaration of ConformityTrademarks CanadaTable of Contents Important Operating Considerations for Safety Introduction Product specificationsAccessories Online registrationConnector panel IN1503 Positioning the projectorIN1501 Table 1 IN150166/1.7 90/2.355/1.4 150/3.8DisplayLink Connecting a computer sourceConnecting power VGA connectionDisplaying an image ? No start up screen? Get help on pageAdjusting the image 169 screen 43 mode 169 mode Native mode NTSC only What is Aspect Ratio?43 screen HDMI 1.3 connection Connecting a video deviceComposite video connection VGA connectionShutting down the projector Troubleshooting your setupTable 3 Status indicator light behavior and meaning Screen Save TimePlug power cord into the projector Problem No start up screenSolution press power buttonResult Computer image projected Problem No computer image, just the words “Signal out of range”Only my laptop’s background appears, not the Desktop icons Background and Desktop projectedresolution of the projector Start Settings Control ProblemSet your computer’s display resolution to the native Panel Display Settings tabImage not square Adjust Keystone on keypadAdjust Sharpness in the Basic Picture menu Square imageAdjust color, tint, brightness, contrast in the Basic Turn off Ceiling Mount in Setup menuTurn off Rear Project in Setup menu Image upside downStartup Screen The video embedded in my PowerPointfor video troubleshooting information presentation does not play on the screenwon’t turn on, Lamp light is turned on “Replace lamp” message appears at startup, lampLamp must be replaced see page lamp doorUsing the remote control Troubleshooting the remoteTroubleshooting Audio Using the audioUsing the projector’s speakers Using the keypad buttons Presentation features Optimizing computer imagesOptimizing video images Customizing the projectorUsing the menus Basic Picture menu Advanced Picture menu Setup menu To enter the PIN at projector startup To change the PINProjector Info a read-only display of current projector settings Status and Service menuSource Info a read-only display of current source settings Factory Reset restores all settings to their defaultImage File Types Using LitePort IN1503 onlyUsing the LitePort Menu Viewing a Slide ShowDisplaying PowerPoint Slides Troubleshooting LitePort Cleaning the lens MaintenanceUsing the security lock WARNINGSReplacing the projection lamp Page I Image INDEXNumerics
Top Page Image Contents