Display OSD/Blanking | Marantz VP-12S4 specs

Display

OSD/Blanking

ENGLISH

Standard 1

Fine Menu 1

Fine Menu 2

Input Signal

RGB/HD Adjust

Display

OSD/Blanking

Config.

Keystone	0
Scale	0
Width	0
Position H	0
Position V	0
Installation	Front

Standard 1

Picture Adjust

Fine Menu 1

Fine Menu 2

Input Signal

RGB/HD Adjust

Display

OSD/Blanking

Config.

	Menu Position	Top-L
	Language	English
	Status Info.	Enable
	Power-OFF Confirm.	Enable
	Blanking Memory	Memory 1
	Blanking Top	0

	Blanking Bottom	0

	Blanking Left	0

	Blanking Right	0

Item	Adjustments
Keystone (Electronic vertical	-50	0	50
keystone correction)	( )	( )	( )
Scale	-100		0
	(Min)		(Max)
Width	-100		0
	(Min)		(Max)
Position H	-50	0	50
	(Left)	(Default)	(Right)
Position V	-50	0	50
	(Down) (Default)		(Up)
Installation	Front, Rear, F+Ceiling,
	R+Ceiling

–Keystone

Adjust trapezoid image to rectangle image.

–Scale

Reduces the image without changing the aspect ratio. The image can be reduced to about 70% the original size.

–Width

Reduces the image width without changing the image height. The width can be reduced to about 75% the original size.

–Position H, V

Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the vertical position of the input signal.

However, when Scale and Width are set to their default settings, the picture position cannot be adjusted.

–Instllation

Sets the installation mode of the projector.

Front: Select to set the projector on a tabletop and project from in front of the screen.

Rear: Select to set the projector on a tabletop and project from behind the screen.

F + Ceiling: Select to mount the projector on the ceiling and project from in front of the screen.

R + Ceiling: Select to mount the projector on the ceiling and project from behind the screen.

Item		Adjustments
Menu Position	Top-L, Top, Top-R, Center-L, Center, Center-R,
	Bottom-L, Bottom, Bottom-R
Language	English, Deutsch, Français, Español,
	Português, Italiano
Status Info.	Enable, Disable
Power-OFF Confirm.	Enable, Disable
Blanking Memory	Off, Memory 1, Memory 2, Memory 3
Blanking Top	0		100

Blanking Bottom	0		100

Blanking Left	0		100

Blanking Right	0		100

–Menu Position

OSD position is selected from 9 positions.

–Status Info.

Enable: Displays the current status of the projector for a set amount of time in the upper right-hand corner of the screen at startup and whenever the Input Source, Picture Mode, Aspect ratio or other setting is changed.

Disable: Does not display Status Info.

–Power-OFF Confirm.

Disable: Directly puts the projector on standby without displaying the confirmation message when power

is shut off from the button on the remote controller or the /I button on the projector. Enable: Displays a confirmation message asking whether to shut the power off or continue use

when power is shut off from the button on the remote controller or the /I button on the projector. To shut off the power immediately, select “Yes” and press the ENTER button. To not shut off the power, select “No” and press the ENTER button.

–Blanking Memory

Sets the blanking mode with which part of the screen can be hidden in black bands. To use this mode or change the setting, select from Memory 1 to 3.

Off:	Turns the blanking mode off. No masking occurs.

Memory 1-3: Memorize the blanking width of the top, bottom, left and right masks set with the below features. Up to three settings can be memorized.

–Blanking Top, Bottom, Left and Right

Set the blanking width of the top, bottom, left and right masks, which are then memorized in Memory 1

– 3 of Blanking Memory. Each can be set from 0 (no mask) to a maximum 100.