Rear and Terminals View
IR sensor | 13 |
Lamp cover
Lamp cover 
securing screw 14
!4AC IN (☞ P.8)
Connect the supplied AC power code.
❖Terminals
zRGB IN
Connect the analog RGB output from an IBM VGA or compatible equipment.
xCOMPONENT VIDEO IN
Y, PB/CB, PR/CR connectors.
Connect the COMPONENT VIDEO output from video equipment or an A/V processor/receiver with a component video output.
c
Connect the
vVIDEO IN
Connect the composite video output from a video equipment.
bTRIG.1(TRIGGER 1)
Terminals
1 |
|
|
| 2 |
|
|
|
| 3 |
|
| 4 |
|
|
|
| 5 |
| 6 | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
| 8 |
| 9 |
| 10 |
| 11 |
•When connecting to component which is not equipped with a remote sensor, be sure to connect the component to the "REMOTE CONTROL OUT" jack of this projector.
. REMOTE switch (EXT. / INT.)
When using this projector independently, set this switch to "INT.". When using this projector in a system with a Marantz DVD player or AV Receiver equipped with a remote sensor, set the switch to "EXT.".
⁄0LIGHT ON/OFF
Select ON : The terminal panel lights up.
Connect the digital RGB signal (TMDS compliant, single link only)
Note: To use the
Bottom View
ENGLISH
When the unit is turned on, 12V is output. When the unit is turned off, no voltage is output. This allows such as a powered up/down screen,whenever the projector is turned on or off.
Note:
To connect with external devices, use an ordinal 35mm mini- plug (mono) cable with attaching the supplied ferrite core.
nTRIG.2(TRIGGER 2)
Select ON or OFF at each aspect mode, such as Full, Normal, Zoom, and Through to control screen aspect ratio with powered up/down dual aspect ratio screen.
Notes:
•Do not use TRIG.1 and TRIG.2, as the power source.
•To connect with external devices, use an ordinal 35mm mini- plug (mono) cable with attaching the supplied ferrite core.
13
15
Adjustable
feet
13
16
15
m
Connect the
,REMOTE CONTROL IN/OUT
By connecting this projector to another Marantz audio component using a supplied System Control cable, you can remotely operate the components as a single system.
•When connecting to component with a remote sensor (such as the SR9200,SR8200), be sure to connect the "REMOTE CONTROL IN" jack of this projector to the "REMOTE CONTROL OUT" jack of the component with the remote sensor.
16Adjustable feet
!5Adjustment lever (☞ P.11)
Lift the projector and turn the adjustment lever right or left. The adjustable feet will extend from the projector. Then, release the lever, the adjustable feet is locked.
!6Screw holes for ceiling mount kit
5