JVC DT-V20L3D Dear Customer, Information for Users on Disposal of Old Equipment, EMC Supplement

Page 3
Attention: This symbol is only valid in the European Union.

U.S.A. only

European Union only

FCC NOTICE

CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IMPORTANT RECYCLING INFORMATION

This product has a fluorescent lamp that contains mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities or for USA, the Electronic Industries Alliance: http://www.eiae.org

WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTHING CONNECTION.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.

REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

IMPORTANT SAFETY INSTRUCTIONS

1)

Read these instructions.

2)

Keep these instructions.

3)

Heed all warnings.

4)

Follow all instructions.

5)

Do not use this apparatus near water.

6)

Clean only with dry cloth.

7)

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8)

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

 

amplifiers) that produce heat.

9)

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one

 

wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the

 

third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for

 

replacement of the obsolete outlet.

10)

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point

 

where they exit from the apparatus.

11)

Only use attachments/accessories specified by the manufacturer.

12)

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or

 

sold with the apparatus. When a cart is used, use caution when moving the cart/

 

apparatus combination to avoid injury from tip-over.

13)

Unplug this apparatus during lightning storms or when unused for long periods of time.

14)

Refer all servicing to qualified service personnel. Servicing is required when the

 

apparatus has been damaged in any way, such as power-supply cord or plug is

 

damaged, liquid has been spilled or objects have fallen into the apparatus, the

 

apparatus has been exposed to rain or moisture, does not operate normally, or has

 

been dropped.

15)

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be

 

placed on the apparatus.

16)

Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

17)

When discarding batteries, environmental problems must be considered and the local rules or laws governing the

 

disposal of these batteries must be followed strictly.

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.

European representative of Victor Company of Japan, Limited is:

JVC Technical Services Europe GmbH Postfach 10 05 04

61145 Friedberg Germany

Information for Users on Disposal of Old Equipment

[European Union]

This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of- life. Instead, the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment, recovery and recycling in accordance with your national legislation.

By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health which could otherwise

be caused by inappropriate waste handling of this product. For more information about collection point and recycling of this product, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

(Business users)

If you wish to dispose of this product, please visit our web page www.jvc-europe.com to obtain information about the take-back of the product.

[Other Countries outside the European Union]

If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment.

EMC Supplement

This equipment is in conformity with the provisions and protection requirements of the corresponding European Directives. This equipment is designed for professional video appliances and can be used in the following environments:

•Controlled EMC environment (for example purpose built broadcasting or recording studio), and rural outdoors environment (far away from railways, transmitters, overhead power lines, etc.)

In order to keep the best performance and ensure electromagnetic compatibility, we recommend to use cables not exceeding the following length:

Cable

Length

Power cord

2.0 m

(attached cable (H05VV-F 3 x 0.75 mm2))

 

Video signal cable

2.0 m

(coaxial cable)

 

Audio signal cable (shielded cable)

1.5 m

DVI cable (shielded cable)

1.5 m

RS-232C cable (shielded cable)

2.0 m

(A straight cable with a D-sub 9-pin connector)

RS-485 cable (twist pair cable)

2.0 m

(A straight LAN cable)

 

REMOTE cable (twist pair cable)

2.0 m

(A straight LAN cable)

 

The inrush current of this apparatus is 6 ampere.

CAUTION

In case where the strong electromagnetic waves or magnetism are near the audio cable or the signal cable, the sound or the picture will contain noise. In such cases, please keep the cable away from the sources of the disturbance.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents DT-V24L3D These openings must not be blocked or covered Safety PrecautionsHow to replace the fuse This product for protection against electric shockDear Customer Information for Users on Disposal of Old EquipmentEMC Supplement Installation To install the standTo detach the stand Higher position Lower position To adjust the stand heightFix the monitor to a wall by using strings To prevent an accidental fallFront panel Daily Operations / ConnectionsPress Menu button Press or button when a menu is not displayedDisplay the menu Press buttons to select an item, then press buttonRear panel Attaching the power cord holderSpecification of the DVI-D Hdcp terminal Available signalsVideo signals Computer signals preset DVI-D Hdcp terminalsOperation guide Menu Configuration-MAIN MenuSetting value -20 +20 Picture FunctionSetting of Area MARKER, Safety MARKER, R-AREA Marker Settings for marker functions 1/2MARKER*1*2 Adjustment bar Settings of E.AUDIO GroupWave Form SETTING*1 Example of the wave form monitorSync Function Settings of SD43 Large Settings of sub menu PosiInformation Setting of Character SETSettings for the information display of the monitor Control Lock Setting value OFF, onMAKE/TRIGGER system External ControlAbout the external control Control priority is as followsFunctions controlled by the MAKE/TRIGGER system Using the MAKE/TRIGGER systemTo assign the functions to the pin terminals Operation of the external controlBasic command list Using the serial communicationCommunication specifications Command outlineTroubleshooting Self-check program Maintenance20Specifications GeneralInput/output terminals Dimensions Unit mm inch Front viewSide view Page DT-V24L3D/DT-V20L3D Multi Format LCD Monitor

DT-V20L3D, DT-V24L3D specifications

The JVC DT-V24L3D and DT-V20L3D are professional broadcast monitors designed to cater to the demanding needs of video production environments. These monitors are particularly engineered to provide high-quality imaging that meets the rigorous standards of broadcast and production professionals.

One of the standout features of these monitors is their LCD technology, which offers remarkable brightness and color accuracy. The DT-V24L3D features a 24-inch display, while the DT-V20L3D has a slightly smaller 20-inch screen. Both monitors utilize a panel with a resolution of 1920 x 1200 pixels, ensuring that footage is presented in sharp detail. This high resolution is particularly beneficial for critical monitoring tasks, as it provides a clear representation of image quality.

Color reproduction is another highlight of these models. They support a wide color gamut, allowing users to view footage with accurate color representation that adheres to industry standards. Their ability to cover various color spaces, including Rec. 709 and others, ensures that color grading can be performed with confidence. The monitors also feature built-in 10-bit processing, which enhances color depth and transitions, making them suitable for HDR workflows.

In terms of connectivity, the DT-V24L3D and DT-V20L3D are equipped with a versatile array of inputs. They feature HDMI, SDI, and composite inputs, among others. This extensive compatibility allows them to be integrated into various studio setups and facilitates seamless connection with different types of equipment, making them ideal for multi-camera operations.

Both monitors are also designed with user-friendly controls, allowing operators to easily adjust settings for brightness, contrast, and color calibration. They come with various preset modes tailored for specific viewing conditions, which aids in achieving optimal visual performance.

Additionally, these models support advanced features such as waveform monitoring, vector scope, and a range of display assist tools that are vital for broadcast and production environments. This enables professionals to make informed decisions while monitoring live feeds or recordings.

Overall, the JVC DT-V24L3D and DT-V20L3D monitors deliver exceptional performance, advanced technology, and reliability that professionals demand in video production. Their combination of high-resolution screens, extensive connectivity, and comprehensive monitoring features make them invaluable tools for any broadcast and production workflow.
Top Page Image Contents