JVC DT-V24L3D, DT-V20L3D specifications Rear panel, Attaching the power cord holder

Page 8

Daily Operations / Connections (cont.)

7Rear panel

1

2

8 AUDIO ASSIGN (MONITOR OUT) terminals

(pin jack)

Output terminals for the analog audio signal.

•

The terminals output the audio signal through

 

AUDIO ASSIGN (IN 1 or IN 2) terminals when

 

you select the video input you have selected for

 

“AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” in

 

“AUDIO SETTING” (☞ page 12).

•

The signal is output from this terminal only when

 

the monitor is on or in “P.SAVE” (power save)

 

mode. (☞ “NO SYNC ACTION” on page 13)

• The EMBEDDED AUDIO signal...

 

– is decoded into an analog signal, then emitted.

 

– is emitted only when “SDI 1” or “SDI 2” is

 

selected, and when EMBEDDED AUDIO

 

signals come in to the E. AUDIO HD/SD SDI

8

Note for connections

•Before making any connections, turn off all the equipment.

•Use a cord whose plugs correctly match the terminals on this monitor and the equipment.

•Plugs should be firmly inserted; poor connections could cause noise.

•When unplugging a cord, be sure to grasp its plug and pull it out.

•DO NOT connect the power cord until all connections are complete.

•Refer also to the user manual of each piece of equipment.

Attaching the power cord holder

Security slot

Attach a security wire to this slot.

The illustration of the monitor is of DT-V24L3D.

1 Power switch

(IN 1 or IN 2) terminal.

– has priority over the audio signal input to

AUDIO ASSIGN (IN 1 or IN 2) terminals when

“SDI-1” or “SDI-2” is selected for “AUDIO1

ASSIGN.” or “AUDIO2 ASSIGN.” and the

EMBEDDED AUDIO signal is input to E.AUDIO

HD/SD SDI (IN 1 or IN 2) terminal.

The provided power cord holder prevents accidental disconnection of the AC power cord from the AC IN terminal.

•The power cord holder consists of two parts, a case and a cover.

1

Case

AC IN terminal

 

 

Turns the power on or off.

 

• You need to press

 

 

 

 

button (☞ u on page

 

 

 

 

6) to use the monitor after turning on the power

switch.

 

2AC IN terminal

AC power input connector.

Connect the provided AC power cord to an AC outlet.

•Attach the provided power cord holder to prevent accidental disconnection of the AC power cord (☞ on the right).

CAUTION

6 EXT.SYNC (CS) terminals (BNC)

Input (IN) and output (OUT) terminals for the

9E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC) Input terminals for the HD/SD SDI signals.

•The terminals accept also EMBEDDED AUDIO signals including up to 12 audio channels with a sampling frequency of 48 kHz.

p E. AUDIO HD/SD SDI (SWITCHED OUT) terminal

(BNC)

Output terminal for the HD/SD SDI signals.

• The SDI signals of the current input (SDI 1 or SDI

2) are re-clocked, then emitted.

• When an input other than SDI 1 and SDI 2 is

selected, the SDI signal of the input selected last

2

3

Cover

Do not connect the power cord until all other connections are completed.

3REMOTE terminal

Terminal for controlling the monitor by an external control. (☞ “External Control” on page 16)

4VIDEO (INPUT 1/INPUT 2) terminals (BNC) Input (IN) and output (OUT) terminals for the composite signals.

5COMPO./RGB (G/Y, B/PB/B-Y, R/PR/R-Y) terminals (BNC)

Input (IN) and output (OUT) terminals for the analog component (color difference) or analog RGB signals.

•Select the signal type in “COMPO./RGB SEL.” corresponding to the type of the input signal (☞ page 10).

external composite sync (Cs) signals.

• To use these terminals, set “SYNC INPUT SEL.”

to “EXT.” (☞ “SYNC FUNCTION” on page 13)

• The terminals are for all VIDEO (INPUT 1, INPUT

2) and COMPO./RGB.

• When an external sync signal is input, external

synchronization has priority over all VIDEO 1,

VIDEO 2 and COMPO./RGB input.

7AUDIO ASSIGN (IN 1/IN 2) terminals (pin jack) Input terminals for the analog audio signals.

•Use this terminal for the analog audio connection of the SDI.

•Select the video input to assign the audio signal in “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” (☞ “AUDIO SETTING” on page 12).

time is emitted from this terminal.

• The signals are emitted from this terminal only

when the monitor is on or in “P.SAVE” (power

save) mode.

qDVI-D (HDCP) terminal

Input terminal for the DVI-D signal compatible with HDCP.

•When the picture is not displayed correctly, change the setting of “DVI INPUT SEL.” (☞ page 10).

CAUTION

•Use only the provided screws.

•Make sure the plug will not be pulled out after the cover is attached to the case.

To detach the cover

Using the audio level meter

You can check the conditions of the current EMBEDDED AUDIO signals in the audio level meter. (☞ “On the Information Display” on page 7)

Make the setting for the level meter in “LEVEL METER SETTING” (☞ “AUDIO SETTING” on page 12).

Page 7 Page 9
Image 8
Page 7 Page 9
Contents DT-V24L3D Safety Precautions How to replace the fuseThis product for protection against electric shock These openings must not be blocked or coveredEMC Supplement Dear CustomerInformation for Users on Disposal of Old Equipment To detach the stand InstallationTo install the stand To adjust the stand height Fix the monitor to a wall by using stringsTo prevent an accidental fall Higher position Lower positionDaily Operations / Connections Front panelPress or button when a menu is not displayed Display the menuPress buttons to select an item, then press button Press Menu buttonAttaching the power cord holder Rear panelAvailable signals Video signalsComputer signals preset DVI-D Hdcp terminals Specification of the DVI-D Hdcp terminalMenu Configuration-MAIN Menu Setting value -20 +20Picture Function Operation guideMARKER*1*2 Setting of Area MARKER, Safety MARKER, R-AREA MarkerSettings for marker functions 1/2 Settings of E.AUDIO Group Adjustment barSync Function Wave Form SETTING*1Example of the wave form monitor Settings of sub menu Posi Settings of SD43 LargeSetting of Character SET Settings for the information display of the monitorControl Lock Setting value OFF, on InformationExternal Control About the external controlControl priority is as follows MAKE/TRIGGER systemUsing the MAKE/TRIGGER system To assign the functions to the pin terminalsOperation of the external control Functions controlled by the MAKE/TRIGGER systemUsing the serial communication Communication specificationsCommand outline Basic command listTroubleshooting Maintenance20 Self-check programInput/output terminals SpecificationsGeneral Side view Dimensions Unit mm inchFront view Page DT-V24L3D/DT-V20L3D Multi Format LCD Monitor

DT-V20L3D, DT-V24L3D specifications

The JVC DT-V24L3D and DT-V20L3D are professional broadcast monitors designed to cater to the demanding needs of video production environments. These monitors are particularly engineered to provide high-quality imaging that meets the rigorous standards of broadcast and production professionals.

One of the standout features of these monitors is their LCD technology, which offers remarkable brightness and color accuracy. The DT-V24L3D features a 24-inch display, while the DT-V20L3D has a slightly smaller 20-inch screen. Both monitors utilize a panel with a resolution of 1920 x 1200 pixels, ensuring that footage is presented in sharp detail. This high resolution is particularly beneficial for critical monitoring tasks, as it provides a clear representation of image quality.

Color reproduction is another highlight of these models. They support a wide color gamut, allowing users to view footage with accurate color representation that adheres to industry standards. Their ability to cover various color spaces, including Rec. 709 and others, ensures that color grading can be performed with confidence. The monitors also feature built-in 10-bit processing, which enhances color depth and transitions, making them suitable for HDR workflows.

In terms of connectivity, the DT-V24L3D and DT-V20L3D are equipped with a versatile array of inputs. They feature HDMI, SDI, and composite inputs, among others. This extensive compatibility allows them to be integrated into various studio setups and facilitates seamless connection with different types of equipment, making them ideal for multi-camera operations.

Both monitors are also designed with user-friendly controls, allowing operators to easily adjust settings for brightness, contrast, and color calibration. They come with various preset modes tailored for specific viewing conditions, which aids in achieving optimal visual performance.

Additionally, these models support advanced features such as waveform monitoring, vector scope, and a range of display assist tools that are vital for broadcast and production environments. This enables professionals to make informed decisions while monitoring live feeds or recordings.

Overall, the JVC DT-V24L3D and DT-V20L3D monitors deliver exceptional performance, advanced technology, and reliability that professionals demand in video production. Their combination of high-resolution screens, extensive connectivity, and comprehensive monitoring features make them invaluable tools for any broadcast and production workflow.
Top Page Image Contents