JVC GD-V502PCE manual Connections, Speakers, AC cord fixing

Page 7

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

SPEAKERS

Terminals (L)

1
2	1
	1
	2

	SPEAKERS	AC cord connection
	Terminals (R)	AC cord connection
	Terminals (R)	(see page 12)
		(see page 12)
		– AC cord fixing

Note: Connect the power cord before combining with accessories such as the pedestal. When combining with accessories such as the pedestal, be very careful not to pinch the power cord.

1. Open the clamper.	2. Insert the AC cord and
	close the clamper
	securely.

3.Slide up the clamper and fix the AC cord plug securely.

When loosen the clamper:

Clamper

AC cord

Note: The power plug in the illustration may not be the type fitted to your set.

– Cable fixing bands Secure any excess cables with bands as required.

Pass the attached cable fixing band through the clip as shown in the figure.

To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure.

While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band.

1

2

To tighten:

To loosen:

Push the catch

Pull

Pull

Optional Terminal Board insert Slots (covered)

AUDIO

PC IN

SERIAL

SLOT1SLOT2

Note:

Insert the optional terminal boards before combining the Plasma Display with the pedestal.

SLOT3

From EXTERNAL monitor terminal on Computer (see page 8)

From SERIAL terminal on Computer

7

Image 7

Contents Plasma Display Monitor GD-V502PCEINSTRUCTIONS Table of Contents Green-and-Yellow Earth Important Safety NoticeFor Your SAFETY, Please Read the Following Text Carefully This Apparatus Must be EarthedSetup Safety PrecautionsWhen using the Plasma Display If problems occur during use Cleaning and maintenanceElectric shocks can result if this is not done Accessories Supply AccessoriesRemote Control Batteries Speakers ConnectionsAC cord fixing SDA HD/SYNC SCL Signal Names for mini D-sub 15P ConnectorGND Ground Signal Name PC Input Terminals connectionCommunication parameters Installing the ferrite core Large sizeCommand Serial Terminals connectionBasic Controls Off Connecting the AC plug to the Wall Outlet Power On/Off and input signal selectionPower On/Off Power Indicator Remote Control SensorEnglishus Select the input signalSelecting the On-Screen Menu Language INPUT1 INPUT2 INPUT3On-Screen Menu Displays Press to Set up Press to access each adjust screen From the unitPress to Setup To setup Multidisplay screenJust Mode Picture ExplanationAspect Controls ZoomPos Adjusting Picture Pos./SizeAdjusting screen Helpful Hint N / Normalise NormalisationCinema Picture AdjustmentsNormal DynamicAGC Advanced settingsMute Sound AdjustmentSelect the magnification required for the enlarged display Digital ZoomDisplay the Operation Guide Select the area of the image to be enlargedPresent Time Present Time Setup / Set up TimerPresent Time Setup Press to exit from Present Time SetupDisplay the Set up Timer screen Press to select Set up TimerReversal / Scroll selection Mode selectionStart setting Screensaver For preventing after-imagesReduces screen after-image Setup of Screensaver TimePress to select Screensaver This function may be applicable to the non-picture area Side Panel AdjustmentCustomizing the Input labels Reduces power consumptionINPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB3 How to Setup Multi Display Setup for Multi DisplayNTSC, PAL, Secam Press to select 2 ⋅ 2, 3 ⋅RGB Setup for Input SignalsComponent/RGB-in Select 3D Y/C Filter For Ntsc AV imagesPAL Secam Ntsc Colour system / Aspect AutoCinema reality If the picture image becomes unstableDisplays the H Horizontal/V Vertical frequencies Setting RGB sync signalSync Freq. kHz/V-Freq. HzPlasma Display panel Symptoms Check TroubleshootingApplicable input signals for PC Input Mini D-sub 15P ∗ Mark Input signal can be displayedGD-V502PCE SpecificationsGD-V502PCE Plasma Display Monitor