JVC GV-PT2 manual Place two R6 batteries, Compartment. Align the batteries as shown

Page 12

PREPARATION OF THE REMOTE CONTROL (RC) UNIT EN 11

How to install the batteries

Place two R6 batteries in the

How to aim the remote control unit

compartment. Align the batteries as shown.

Remote control signal receiver

Approx.

30°

Within 5 m

Operating distance depends on the ambient brightness and the angle at which the RC unit is aimed at the receiver.

Notes on the batteries

●Remove the batteries from the RC unit when not using it for a long period.

●If the RC unit does not work properly, remove the batteries from the unit and let it stand for a while, then replace the batteries and try using it again.

When to replace the batteries:

●When the remote control’s operating distance starts to decrease, it means that the battery level is dropping. In this case, replace the batteries with new ones.

When replacing the batteries

●Use two R6 batteries.

●Replace both batteries at the same time. Do not mix new batteries with used batteries.

●Insert the batteries in accordance with the + and – indications.

●Be sure to read the precautions on the battery label.

Image 12

Contents GV-PT2 Safety Precautions Some Dos And Donts On The Safe Use Of Equipment Above ALLAbout Thermal Heads Inset Print Title Impose PrintStrobe Print Editing IndexLayout Print BUILT-IN Capture FacilityContents Paper Tray Blank Paper Sheet Set Remote Control UnitFloppy Disk Error lamp INK lamp Remote Control Signal Receiver Remote Pause connector@ S-Video Input Connector # Video Input ConnectorParallel Connector Service Door for Jammed Paper RemovalJlip Joint Level Interface Protocol Connector Video Output Connector10 EN Transmitter Source select button Title buttonMenu control button Cursor control button OK button Place two R6 batteries Compartment. Align the batteries as shownUse two R6 batteries EN C Onnections Image source with Video output connectors When removing ink cassette 14 ENSET Contents Uses About Blank Paper Sheet Sets optionalOpening the paper tray Inserting blank paper sheets in the paper trayLoading/unloading the paper tray Open the lid while pushing aPreparation EN Preparation Select Layout and NO. of ScenesPress OK Press Memory When the DE- Sired Image Appears To print a live image using a camcorder as the sourcePress Print If you store the wrong image or store an image incorrectlySetting with remote control unit Print menu displayPress Menu Select Layout 22 EN Multi-Print Same ScenePress Format Print Lamp blinks, indicating that printing Has startedNow printing!! appears on screen during Printing24 EN Multi-Print Different ScenesBegin Source Playback Fast-forward or rewind the source tape to findDesired scene, then start playback a little Before the scenePress Mode Mode Select Menu appears on the monitor26 EN Multi-Print Different Scenes Sticker Type PrintPress Memory When the Desired Image Appears To exit Editing Index modeTitle Impose Print is not available If you store a wrong image or store an image incorrectly28 EN Inset PrintStore the main scene Select Horizontal on Layout and Select OFF on MultiSelect 4 or 16 on Multi and Select Different on Content Store the sub sceneIf you store the wrong main scene If you store the wrong sub scene30 EN Strobe PrintPress Memory When the DE- Sired Image Appears 32 EN Vertical Layout PrintSelect Vertical on Layout Image to be stored 34 EN Video Cassette Label PrintSelectout Video Cassette on LAY Press cursor buttons / to choose the optionsTo affix labels on video cassettes First cut out the labels and then stick onto video cassettes36 EN Name Sticker PrintPress Memory When the DE- Sired Image Appears 38 EN Calendar PrintStore the Desired Image in Memory SET YEAR/MONTH of Calendar Press OK ButtonIf you store the wrong calendar 40 EN Editing IndexConnect Image Source Camcorder or VCR to Printer page 12 SET EDIT-IN or EDIT-OUT Point of the Scene to be StoredChoose Editing Index Sequence for memory42 EN Snapshot PrintSelect Snap Shot Printing Press the CAMCORDER’S SnapShot Button 44 EN Title Impose PrintRecord Title or Drawing with Your Camcorder Erase title when printing is finished Choose NEGATIVE/POSITIVE of the TitleIf you want to change the title If you want to change Colour orUsing The Attached Collection Of Superimpose Patterns 46 ENShooting a pattern Personal Computer Printer Section EN Introd Uction Bi-Directional 25-pin printer interface 486DX2 or higher CPUEdit FormatImage WindowTo Video Output connector To S-VIDEO Video cable optionConnector Printer Front panel jack To S-VIDEO Input connector To Video Input connectorRear panel jack To Video Personal ComputerSetting up EN INS T Alling T HE SoftwareRun 54 EN Windows 3.1 offers a number of ways to launch an applicationClosing the Program Maximize buttonEach menu is configured as shown below 56ENRotate 90 clockwise 58 EN Tile CascadeArrange Icons Printing Procedure Press OK60 EN ExampleCall up the printer setup display setup dialog To start printingPrint orientation Select when printing Image adjustmentCancel No. of prints Print orientationFile name box Message box Displays the current status Control button64 EN PC mode is selected Video printer modePaper jammed Close back door66 EN To the PC mode Capture mode isSelected. Switch to PC mode68 EN If no paper is jammed Slot of the paper trayIf no paper is jammed in the output tray Power Power consumptionSignal ConnectorsError Messages Pg ,23-43Layout Pg ,43,59MEM O Memo GV-PT2