JVC GV-PT2 manual Press Memory When the Desired Image Appears, Title Impose Print is not available

Page 28

EN 27

Display of stored position

Input video display

4 BEGIN SOURCE PLAYBACK Fast-forward or rewind the source tape to find the desired scene, then start playback a little before the scene.

5 PRESS MEMORY WHEN THE DESIRED IMAGE APPEARS

•The image is stored in memory. However, the stored image is not shown and the screen continues to display the input video.

•The next position to be stored in memory appears in all white in the upper righthand corner of the screen.

6 REPEAT STEP 5 FOR EACH IMAGE YOU ARE GOING TO PRINT (UP TO 16) AND STORE THEM

•After 16 images have been stored in memory, the MEMORY display appears.

•If you want to end memory storage before 16 images have been captured, press OK. The MEMORY display appears, on which empty positions are shown in white.

•Title Impose Print is not available.

7 PRESS PRINT

•The Print Lamp blinks, indicating that printing has started.

•“Now printing!!” appears on screen during printing.

•When the printed sheets are delivered to the output tray and “Now printing!!” disappears, printing is complete. Do not leave more than 25 printed sheets stacked on the tray.

To exit EDITING INDEX mode...

Press MODE after printing and the EDITING INDEX display disappears.

If you store a wrong image or store an image incorrectly...

It is not possible to correct a wrong image once it has been stored in memory. Press MODE to release the EDITING INDEX mode and then perform steps 1 to 6 from the beginning again.

FRAME STABILISER for unstable image correction...

Switching the FRAME STABILISER ON/OFF is not available in the EDITING INDEX mode.

Image 28

Contents GV-PT2 Safety Precautions Some Dos And Donts On The Safe Use Of Equipment Above ALLAbout Thermal Heads Inset Print Title Impose PrintStrobe Print Editing IndexLayout Print BUILT-IN Capture FacilityContents Control Unit Paper Tray Blank Paper Sheet Set RemoteFloppy Disk Error lamp INK lamp Remote Control Signal Receiver Remote Pause connector@ S-Video Input Connector # Video Input ConnectorParallel Connector Service Door for Jammed Paper RemovalJlip Joint Level Interface Protocol Connector Video Output ConnectorTransmitter Source select button Title button 10 ENMenu control button Cursor control button OK button Compartment. Align the batteries as shown Place two R6 batteriesUse two R6 batteries EN C Onnections Image source with Video output connectors When removing ink cassette 14 ENSET Contents Uses About Blank Paper Sheet Sets optionalOpening the paper tray Inserting blank paper sheets in the paper trayLoading/unloading the paper tray Open the lid while pushing aPreparation EN Select Layout and NO. of Scenes PreparationPress OK Press Memory When the DE- Sired Image Appears To print a live image using a camcorder as the sourcePress Print If you store the wrong image or store an image incorrectlyPrint menu display Setting with remote control unitPress Menu Select Layout Multi-Print Same Scene 22 ENPress Format Print Lamp blinks, indicating that printing Has startedNow printing!! appears on screen during Printing24 EN Multi-Print Different ScenesBegin Source Playback Fast-forward or rewind the source tape to findDesired scene, then start playback a little Before the scenePress Mode Mode Select Menu appears on the monitor26 EN Multi-Print Different Scenes Sticker Type PrintPress Memory When the Desired Image Appears To exit Editing Index modeTitle Impose Print is not available If you store a wrong image or store an image incorrectly28 EN Inset PrintStore the main scene Select Horizontal on Layout and Select OFF on MultiSelect 4 or 16 on Multi and Select Different on Content Store the sub sceneIf you store the wrong main scene If you store the wrong sub scene30 EN Strobe PrintPress Memory When the DE- Sired Image Appears Vertical Layout Print 32 ENSelect Vertical on Layout Image to be stored 34 EN Video Cassette Label PrintSelectout Video Cassette on LAY Press cursor buttons / to choose the optionsTo affix labels on video cassettes First cut out the labels and then stick onto video cassettes36 EN Name Sticker PrintPress Memory When the DE- Sired Image Appears Calendar Print 38 ENStore the Desired Image in Memory Press OK Button SET YEAR/MONTH of CalendarIf you store the wrong calendar 40 EN Editing IndexConnect Image Source Camcorder or VCR to Printer page 12 SET EDIT-IN or EDIT-OUT Point of the Scene to be StoredChoose Editing Index Sequence for memory42 EN Snapshot PrintPress the CAMCORDER’S Snap Select Snap Shot PrintingShot Button Title Impose Print 44 ENRecord Title or Drawing with Your Camcorder Erase title when printing is finished Choose NEGATIVE/POSITIVE of the TitleIf you want to change the title If you want to change Colour or46 EN Using The Attached Collection Of Superimpose PatternsShooting a pattern Personal Computer Printer Section EN Introd Uction Bi-Directional 25-pin printer interface 486DX2 or higher CPUEdit FormatImage WindowTo Video Output connector To S-VIDEO Video cable optionConnector Printer Front panel jack To S-VIDEO Input connector To Video Input connectorRear panel jack To Video Personal ComputerSetting up EN INS T Alling T HE SoftwareRun 54 EN Windows 3.1 offers a number of ways to launch an applicationClosing the Program Maximize buttonEach menu is configured as shown below 56ENRotate 90 clockwise Tile Cascade 58 ENArrange Icons Printing Procedure Press OK60 EN ExampleCall up the printer setup display setup dialog To start printingPrint orientation Select when printing Image adjustmentCancel No. of prints Print orientationFile name box Message box Displays the current status Control button64 EN PC mode is selected Video printer modePaper jammed Close back door66 EN To the PC mode Capture mode isSelected. Switch to PC mode68 EN Slot of the paper tray If no paper is jammedIf no paper is jammed in the output tray Power Power consumptionSignal ConnectorsError Messages Pg ,23-43Layout Pg ,43,59MEM O Memo GV-PT2