JVC GV-PT2 manual Safety Precautions

Page 2

SAFETY PRECAUTIONS

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION

■When you are not using the unit for a long period of time, it is recommended that you disconnect the power cord from the mains outlet.

■Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.

The STANDBY/ON button does not completely shut off mains power to the unit, but

switches operating current on and off. " " shows electrical power standby and " " shows ON.

The mains outlet shall be installed near the unit and shall be easily accessble.

NOTE:

The rating plate (serial number plate) and safety caution are on the bottom and/or the back of the main unit.

EN 1

IMPORTANT (for U. K. owners)

Connection to the mains supply in the United Kingdom.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain a proper safety approved extension lead/adapter or consult your dealer.

BE SURE to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover.

If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvert- ent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow the instructions given below:

DO NOT make any connection to the Larger Terminal coded E or Green.

The wires in the mains lead are coloured in accordance with the following code:

Blue to N (Neutral) or

Black

Brown to L (Live) or

Red

If these colours do not correspond with the terminal identifications of your plug, connect as follows:

Blue wire to terminal coded N (Neutral) or coloured Black.

Brown wire to terminal coded L (Live) or coloured Red.

If in doubt — consult a competent electrician.

Image 2

Contents GV-PT2 Safety Precautions Some Dos And Donts On The Safe Use Of Equipment Above ALLAbout Thermal Heads Strobe Print Inset PrintTitle Impose Print Editing IndexLayout Print BUILT-IN Capture FacilityContents Floppy Disk Paper Tray Blank Paper Sheet Set RemoteControl Unit @ S-Video Input Connector Error lamp INK lampRemote Control Signal Receiver Remote Pause connector # Video Input ConnectorJlip Joint Level Interface Protocol Connector Parallel ConnectorService Door for Jammed Paper Removal Video Output ConnectorMenu control button Cursor control button OK button 10 ENTransmitter Source select button Title button Use two R6 batteries Place two R6 batteriesCompartment. Align the batteries as shown EN C Onnections Image source with Video output connectors When removing ink cassette 14 ENSET Contents Uses About Blank Paper Sheet Sets optionalLoading/unloading the paper tray Opening the paper trayInserting blank paper sheets in the paper tray Open the lid while pushing aPreparation EN Press OK PreparationSelect Layout and NO. of Scenes Press Print Press Memory When the DE- Sired Image AppearsTo print a live image using a camcorder as the source If you store the wrong image or store an image incorrectlyPress Menu Setting with remote control unitPrint menu display Select Layout Press Format 22 ENMulti-Print Same Scene Now printing!! appears on screen during Print Lamp blinks, indicating that printingHas started Printing24 EN Multi-Print Different ScenesDesired scene, then start playback a little Begin Source PlaybackFast-forward or rewind the source tape to find Before the scene26 EN Press ModeMode Select Menu appears on the monitor Multi-Print Different Scenes Sticker Type PrintTitle Impose Print is not available Press Memory When the Desired Image AppearsTo exit Editing Index mode If you store a wrong image or store an image incorrectlyStore the main scene 28 ENInset Print Select Horizontal on Layout and Select OFF on MultiIf you store the wrong main scene Select 4 or 16 on Multi and Select Different on ContentStore the sub scene If you store the wrong sub scene30 EN Strobe PrintPress Memory When the DE- Sired Image Appears Select Vertical on Layout 32 ENVertical Layout Print Image to be stored Selectout Video Cassette on LAY 34 ENVideo Cassette Label Print Press cursor buttons / to choose the optionsTo affix labels on video cassettes First cut out the labels and then stick onto video cassettes36 EN Name Sticker PrintPress Memory When the DE- Sired Image Appears Store the Desired Image in Memory 38 ENCalendar Print If you store the wrong calendar SET YEAR/MONTH of CalendarPress OK Button Connect Image Source Camcorder or VCR to Printer page 12 40 ENEditing Index SET EDIT-IN or EDIT-OUT Point of the Scene to be StoredChoose Editing Index Sequence for memory42 EN Snapshot PrintShot Button Select Snap Shot PrintingPress the CAMCORDER’S Snap Record Title or Drawing with Your Camcorder 44 ENTitle Impose Print If you want to change the title Erase title when printing is finishedChoose NEGATIVE/POSITIVE of the Title If you want to change Colour orShooting a pattern Using The Attached Collection Of Superimpose Patterns46 EN Personal Computer Printer Section EN Introd Uction Bi-Directional 25-pin printer interface 486DX2 or higher CPUImage EditFormat WindowTo Video Output connector To S-VIDEO Video cable optionRear panel jack To Video Connector Printer Front panel jackTo S-VIDEO Input connector To Video Input connector Personal ComputerSetting up EN INS T Alling T HE SoftwareRun 54 EN Windows 3.1 offers a number of ways to launch an applicationClosing the Program Maximize buttonEach menu is configured as shown below 56ENRotate 90 clockwise Arrange Icons 58 ENTile Cascade Printing Procedure Press OK60 EN ExampleCall up the printer setup display setup dialog To start printingCancel Print orientation Select when printingImage adjustment No. of prints Print orientationFile name box Message box Displays the current status Control button64 EN Paper jammed PC mode is selectedVideo printer mode Close back door66 EN Selected. Switch to To the PC modeCapture mode is PC mode68 EN If no paper is jammed in the output tray If no paper is jammedSlot of the paper tray Signal PowerPower consumption ConnectorsLayout Error MessagesPg ,23-43 Pg ,43,59MEM O Memo GV-PT2