JVC DLA-SH4K instruction manual Names and Functions of Parts Cont’d, Rear

Page 10

Getting Started

Names and Functions of Parts (Cont’d)

Rear

F G H I J

Q P

O

DVI 1

 

DVI 2

 

CONTROL

 

USB

Exhaust air

LAN

DVI 3

 

 

OPERATE I/B STANDBY/ON

 

LAMP

DVI 4

WARNING

RS-232C

 

N M L K

F[DVI 1 to 4] Terminal

This is an input terminal for video signals. Connect it to the video output terminal of the computer.

(A Page 17, 19)

GVent Hole

Warm air exits from the hole after cooling the projector.

CAUTION:

Do not block the vent holes with papers, cloth, or soft cushions. Doing so may cause heat to trap inside the projector and result in fire or malfunction.

HVent Hole (For Lamp)

Warm air exits from the hole after cooling the lamp.

IMain Power Supply Switch

Use this to turn ON/OFF the main power supply of the projector unit.

JAC Power Input Terminal

Connect the supplied cord to this terminal.

K[STANDBY/ON] Indicator

Lit (Red)

: When in the standby mode.

Lit (Green)

: When power is supplied.

Blinking (Red)

: When in the cooling (cool down)

 

mode. (A Page 23)

Blinking (Green) : When the projected image is temporarily hidden. (A Page 23)

L[LAMP] Indicator

This indicator lights up when the lamp time exceeds 1400 hours.

NOTE:

For details on indicator displays during warnings, refer to “Warnings Using Indicators”. (A Page 41)

A lamp life message appears when the lamp time has exceeded 1500 hours. (A Page 40)

M[WARNING] Indicator

This indicator lights up when abnormality occurs on this projector. For details, refer to “Warnings Using Indicators”. (A Page 41)

N[OPERATE I/B] Button

Pressing this button for one second or longer when in the standby mode (main power supply is ON) turns on the power of the projector unit. Pressing it for one second or longer when the power is ON switches the projector to the standby mode.

O[RS-232C] Terminal

This is the RS-232C interface-specific terminal. This projector can be controlled by connecting it to a computer using a RS-232C cable.

P[LAN] Terminal

Enables control of this projector using a computer that is connected to the network.

NOTE:

For details on indicator displays during warnings, refer to “Warnings Using Indicators”. (A Page 41)

Q[USB] Terminal

Enables control of this projector by connecting it to a computer.

10

Image 10
Contents For Customer use Thank you for purchasing this JVC productAbout the installation place Safety PrecautionsMachine Noise Information Germany only Do not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Safety Precautions Cont’dPower cord NeutralEMC Supplement Contents Check the Accessories/ Optional AccessoriesHigh flexible installation FeaturesHow to Read this Manual User-friendly interface and high operabilityBurning-in of D-ILA Device Precautions During UseMaintenance Procedures Viewing Conditions Brightness of RoomNames and Functions of Parts Front/Right SideNames and Functions of Parts Cont’d Rear When using two sets of projectors side by side Installation When using one set of projector  When the projector is suspendedProjector Installation Installation Cont’dInstalling the Projector and Screen  When shift amount in the left direction is -25 %  When shift amount in the right direction is +25 % When shift amount in the left/right direction is 0 %  When light passes through the glass of projection boothInstalling the Projector and Screen Cont’d Projecting images by arranging projectors side by sideApprox .29 m Screen Size and Projection DistanceApprox .03 m Approx.3.81 mConnection During Single-Screen Mode Display Connecting Video Signals of the Computer Possible Input Signals and Projected Image  Connection During Single-Screen Mode Display Output Status Connecting Video Signals Computer Cont’dConnection During Two-Screen/Four Screen Mode Display NormalConnection Example During Two-Screen Mode  Connection During Two-Screen/Four-Screen Mode DisplayConnection Example During Four-Screen Mode Connection Example Connection Using a LAN CableConfiguring the Network Settings PC for this ProjectorClick Aloginb Using the Mail Delivery FeatureEnter ArootB in Login Name Login screen for this projector appearsProjecting Image Useful Features During Projection Settings Menu Main MenuSignal Status Setting Value Description PowerLatest Error TemperatureSetting Menu Cont’d Image MenuSetting Value Description Input Level Setting MenuDisplay Mode Convergence Menu Setting Value Description RedImage Green color value is fixed Focus This menu is used for adjusting the projection lensLens Menu ShiftOption Menu Network Menu  Error message sent from this projector Mail MenuMail Setting Value Description Mail SettingPassword AddressCommand Format Communication SpecificationsRS-232C Interface  Parameters used for the data format  External control command tableON/OFF Maintenance Cleaning and Replacing the FilterReplacement of Light Source Lamp Routine ServicingTroubleshooting Image is Mode displayWhen Projection has Ended Unusually darkLamp Time Over What to do when these messages are displayedMessage Cause Details Out of RangeIndicator Description Indicators Measures when the warning mode appears Check MeasureLatest Error Specifications DVI-D Terminal Pin No Signal Specifications Cont’dRS-232C Terminal Pin No Signal Operation Signal Direction  Pin Assignment Side Dimensional Outline Drawing Top  Front  RearOthers Page DLA-SH4K Projector