McIntosh MDLP1 Fine Menu 1 Adjust, Fine Menu 2 Adjust, Input Signal Resolution Selection

Page 26

Fine Menu 1 Adjust

In the Fine Menu 1 there are two user type adjustments, image sharpness and noise reduction. The remaining adjustments are best performed by a professional with the necessary video signal generators and optical measurement equipment. Refer to figure 26.

Standard 1

 

 

Picture Adjust

Sharpness

0

Fine Menu 1

Noise Reduction

0

Fine Menu 2

R Gain

0

Input Signal

G Gain

0

RGB/HD Adjust

B Gain

0

Display

R Bias

0

OSD/Blanking

G Bias

0

Config.

B Bias

Figure 26

Sharpness - Effects how soft or sharp the image is.

Noise Reduction - Reduces the amount of electronic noise present in the video signal.

R Gain - This menu allows setting the gain for red. G Gain - This menu allows setting the gain for green. B Gain - This menu allows setting the gain for blue. R Bias - This menu allows setting the bias for red. G Bias - This menu allows setting the bias for green. B Bias - This menu allows setting the bias for blue.

Note : The settings made in Fine Menu 1 are saved in the cur-

rently selected Picture Mode (Default excluded).

Fine Menu 2 Adjust

The following adjustment are intended to be use by a pro- fessional installer to compensate for differences in video signals from various sources. Refer to figure 27.

Standard 1

 

 

Picture Adjust

Cinema

Auto

Fine Menu 1

VCR Mode

On

Fine Menu 2

Black Level

0 IRE

Input Signal

FRC

Auto

RGB/HD Adjust

CEC

Off

Display

Picture Shift V

0

OSD/Blanking

Luminance Gain

0

Config.

Chroma Delay

0

Figure 27

Cinema - Auto: Automatically selects the cinema mode when a video signal is input. NTSC: 3-2 pull down, PAL: 2-2 pull down.

Off: Pull-down processing is not performed.

VCR Mode - On: A projector is forced into the intra-field only deinterlacing mode.

Off: A projector is used with external field memories and operates in the full set of deinterlacing modes, i.e., motion adaptive video deinterlacing and full frame film source deinterlacing using 3:2 pulldown detection (2:2 pulldown for 625/50 sources).

Black level - Select the black level by a video source. FRC - Auto: Frame Rate Conversion function is basically

off. However FRC turns on automatically de- pending on vertical frequency of input signal.

On: Frame Rate Conversion function is On (60Hz fixed).

CEC - On: Chroma Error Correction reduces CUE (Chro- ma Up-sampling Error) of 1080i signals.

Off : Normally, use this mode.

Picture Shift V - When Aspect on the Picture Adjust menu is set to Zoom, this setting allows the user to move the projected image verti- cally in order to see parts on the image not appearing on the screen.

Luminance Gain - This menu allows the users to set the

luminance gain.

Chroma Delay - This menu allows the users to set the chro- minance delay.

Input Signal Resolution Selection

There are several SD (Standard Definition) and HD (High Definition) types of video signals the MDLP1 is capable of displaying. The default setting for the Component Video and HDMI Inputs of the MDLP1 is AUTO. In the AUTO Mode, the MDLP1 will automatically switch to the highest resolution possible for each of the video signals it receives. Refer to figure 28.

Note: The S-Video,Video and RGB Inputs are not used on the MDLP1.

Standard 1

 

 

Picture Adjust

Component 1

Auto

Fine Menu 1

Component 2

Auto

Fine Menu 2

S-Video

Auto

Input Signal

Video

Auto

RGB/HD Adjust

RGB

Auto

Display

HDMI1

Auto

OSD/Blanking

HDMI2

Auto

Config.

CSC HDMI1

Auto

 

CSC HDMI2

Auto

Figure 28

26

Image 26
Contents Video Projector Important Safety Instructions Additional Safety Instructions Safety InstructionsThank You Customer ServiceTable of Contents Please Take a MomentGeneral Information Data Port Connectors Connector and Cable InformationPower Control Connectors RS232 DB9 Connector Pin LayoutPerformance Features Dimensions Installation Installation Overview VentilationProjector placed above the floor Projector and 169 Screen Mounting LocationProjector mounted from the ceiling Installation, con’t Projector and 43 Screen Mounting Location Installation, con’t Initial Setup Screen Rear Panel Connections and Switch AC Power Cord Connections How to Connect the MDLP1Power Control Connections Data Control ConnectionsRemote Control Push-Buttons How to use the Remote Control Front Panel Push-buttons, Indicators and Control Default Settings Menu Function SettingImage Adjustments and Setting changes How to Operate the MDLP1Power Source SelectionKeystone0 Picture Mode Selection Picture Adjust MenuHow to Operate the MDLP1, con’t Aspect Ratio OptionsInput Signal Resolution Selection Fine Menu 1 AdjustFine Menu 2 Adjust OSD/Blanking RGB/HD AdjustDisplay Menu Adjust Config. Settings Lamp at this time, a General Specifications Specifications Optical SpecificationsElectrical Specifications Packing Instructions McIntosh Laboratory, Inc Chambers Street Binghamton, NY