To control an Onkyo component that’s not connected 61 via u, point the remote controller at the compo- nent. Be sure to enter the appropriate remote control code first.
The entered remote control code may not be correct. — If more than one code is listed, try each one.
UP-A1 Dock for iPod
■ There’s no sound
Make sure your iPod is actually playing. | — |
Make sure your iPod is inserted properly in the | — |
Dock. |
|
|
|
Make sure the
Make sure the AV receiver is turned on, the correct — input source is selected, and the volume is turned up.
Make sure the plugs are pushed in all the way. | — |
Try resetting your iPod. | — |
|
|
Recording
■ Can’t record
On your recorder, make sure the correct input is | — |
selected. |
|
|
|
To prevent signal loops and damage to the AV | — |
receiver, input signals are not fed through to outputs |
|
with the same name (VCR/DVR IN to VCR/DVR |
|
OUT). |
|
|
|
Zone 2
■There’s no sound
Only components connected to analog inputs can be — played in Zone 2.
■The Zone 2 speakers produce no sound
To use the Zone 2 speakers, you must set the “Front 54 High/Zone2” setting to “Zone2” .
■There’s no video
Make sure that your iPod model’s TV OUT setting is — set to On.
Make sure the correct input is selected on your TV or — the AV receiver.
Some versions of the iPod do not output video. | — |
■The AV receiver’s remote controller doesn’t control your iPod
Make sure your iPod is properly inserted in the | — |
Dock. If your iPod is in a case, it may not connect |
|
properly to the Dock. Always remove your iPod |
|
from the case before inserting it into the Dock. |
|
The iPod cannot be operated while it’s displaying the — Apple logo.
Make sure you’ve selected the right remote mode. | — |
When you use the AV receiver’s remote controller, | — |
point it toward your AV receiver. |
|
When connecting | — |
| |
Selector switch, you can switch the input source |
|
between |
|
PORT repeatedly on the front panel. |
|
If you still can’t control your iPod, start playback by — pressing your iPod model’s Play button. Remote operation should then be possible.
Try resetting your iPod. | — |
Depending on your iPod, some buttons may not | — |
work as expected. |
|
|
|
■The AV receiver unexpectedly selects your iPod as the input source
Always pause iPod playback before selecting a dif- — ferent input source. If playback is not paused, the Direct Change function may select your iPod as the input source by mistake during the transition between tracks.
Others
■The sound changes when I connect my headphones
When a pair of headphones is connected, the listen- — ing mode is set to Stereo, unless it’s already set to Stereo, Mono or Direct.
■The speaker distance cannot be set as required
In some cases, corrected values suitable for home | — |
theater use may be set automatically. |
|
■How do I change the language of a multiplex source
Use the “Multiplex” setting on the “Audio Adjust” 42 menu to select “Main” or “Sub”.
■The ufunctions don’t work
To use u, you must make an uconnection and an 21 analog audio connection (RCA) between the compo- nent and AV receiver, even if they are connected dig- itally.
■The functions System On/Auto Power On and Direct Change don’t work for components connected via u
These functions don’t work when Zone 2 is turned 21 on.
■When performing “Audyssey 2EQ® Room Correction and Speaker Setup”, the measurement fails showing the message “Ambient noise is too high.”.
This can be caused by any malfunction in your | — |
speaker unit. Check if the unit produces normal |
|
sounds. |
|
En
67