Speaker Configuration
This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup function (➔ 28).
With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify “Full Band” for speakers that can output low fre- quency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover fre- quency will be output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequencies.
■Subwoofer
`Yes:
Select if a subwoofer is connected.
`No:
Select if no subwoofer is connected.
■Front
`Full Band
`40Hz to 100Hz, 120Hz, 150Hz, 200Hz
Note
•If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”.
■Center*1, Surround*1 , Surr Back*2*3*4*5
`Full Band
`40Hz to 100Hz, 120Hz, 150Hz, 200Hz
`None:
Select if no speaker is connected.
■Front High*1*2*4*6
`Full Band
`40Hz to 100Hz, 120Hz, 150Hz, 200Hz
`None:
Select if no speaker is connected.
Note
*1 “Full Band” can be selected only when “Full Band” is selected in the “Front” setting.
*2 If the “Surround” setting is set to “None”, this setting cannot be selected.
*3 If the “Surround” setting is set to anything other than “Full Band”, “Full Band” cannot be selected here.
*4 If the Powered Zone 2 is being used (➔ 54), this setting can- not be selected.
*5 If you have selected other than “Surr Back” in the “Surr- Back/Front High” setting, this setting cannot be selected.
*6 If you have selected other than “Front High” in the “Front High/Zone2” or “SurrBack/Front High” setting, this setting cannot be selected.
■Surr Back Ch
`1ch:
Select if only one surround back speaker is con- nected.
`2ch:
Select if two (left and right) surround back speakers are connected.
Note
•If the “Surr Back” Setting is set to “None” (➔ 48), this setting cannot be selected.
■LPF of LFE
(Low-Pass Filter for the LFE Channel)
`80Hz, 90Hz, 100Hz, 120Hz
With this setting, you can specify the cutoff frequency of the LFE channel’s
■Double Bass
This setting is NOT set automatically by Audyssey 2EQ Room Correction and Speaker Setup function (➔ 28).
With the Double Bass function, you can boost bass out- put by feeding bass sounds from the front left, right, and center channels to the subwoofer.
`On:
Double Bass function on.
`Off:
Double Bass function off.
Note
•This function can be set only if the “Subwoofer” setting is set to “Yes”, and the “Front” setting is set to “Full Band”.
Speaker Distance
This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup function (➔ 28).
Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.
■Unit
`feet:
Distances can be set in feet. Range: “1ft” to “30ft” in 1 foot steps.
`meters:
Distances can be set in meters. Range: “0.3m” to “9.0m” in 0.3 meter steps.
■Left, Front High Left, Center, Front High Right, Right, Surr Right, Surr Back Right, Surr Back Left, Surr Left, Subwoofer
`Specify the distance from the each speaker to your lis- tening position.
Note
•Speakers that you set to “No” or “None” in the
“Speaker Configuration” cannot be selected (➔ 41).
En
41