Elmo HV-C1000XG Replacing the Lamp, Replacement of the lamp requires a work done at a high

Page 38

9 REPLACING THE LAMP

1

Replacing the Lamp

The lamp that is installed in the product has a certain life span. When the lamp is used for a

2 long period, the lamp light may become dark or the lamp may go off due to the end of its life. (The life of the lamp varies according to the utilization condition.) In this case, replace the lamp.

3

4

5

How to replace the lamp


	WARNING		• Use JR12V50W AKM/5EZ-1 manufactured by Phillips for
	WARNING		replacement. Other lamps may blow out or cause fire if used.





			• The lamp is very hot immediately after use. Direct contact
			with the lamp or lamp cover will cause burns. Make sure that
	CAUTION		lamp is thoroughly cooled off (30 minutes or more) before
	CAUTION		replacing the lamp.
			replacing the lamp.
			• Replacement of the lamp requires a work done at a high
			location. Take care not to cause accident.

6

7

8

9

10

11

1.Turn OFF the Power Supply Switch.

2.Remove the power cord.

3.Wait until the lamp is thoroughly cooled off.

4.Remove the lamp cover.

Loosen the fixing screws and displace the lamp cover in the arrow direction. (Fig. 1)

Turn the lamp cover around the fixing screw. (Fig. 2)

5. Replace the lamp.

Rotate the lamp and install a new lamp.

6. Install the lamp cover.

Lamp cover shall be installed in sequence reverseto its removal.

REQUEST

screw

( Fig. 1)

( Fig. 2)

Since the lamp is made of glass, do not touch the glass surface with bare hands, apply a strong impact, or scratch the surface.

37

Image 38

Contents HV-C1000XG Important Safeguards Wash hands after handling Should be moved with care. QuickRisk Electric Shock Do not Open Exclamation point within Before YOU USE Contents Replacing the Lamp Symptoms and ConfirmationUart Communication Format Part Names and Functions AppearanceTo connect the mouse supplied accessory*1 Connector PanelAnalog RGB-out Power Cord RS-232C Terminal RGB OUT ReceptacleACName Function Reference Wireless Remote ControlPower Supply Switch To turn ON/OFF the power supply To double the image size To switch pause/motion of the imageButton Name Function Reference Memory No. Used with 6 toPreparation Wireless Remote ControlReceivable Range Mouse Mouse OperationSetting of Auto Focus Operating Range InstallationInstallation of the Unit Connection to the composite video-out terminal Connection to Monitor and ProjectorConnection to the analog RGB-out terminal Connection to the S video-out terminalOperation Procedures Simple Steps for Presenting Printed MaterialZoom Various Functions and OperationLighting Digital Magnification Mouse can be operated as followsWhen Pause is effective, COLOR/B&W selection does not work Color / B&W SelectionPosi / Nega Conversion Image RotationPause ContrastIris M. Frame Accumulate ModeAuto iris adjustment Focus Auto FocusPower Manual Focus To focus on specific part of the material, such as 3-DPreset Operation Utility Software CD-ROM How to read out stored imagesImage Memory OSD Operation Main Menu Posi/Nega To switch the selection ConversionSelection Emphasis of the image When power is turned ON, PointerFor the mouse pointer ON/OFF Icon Name Function Reference Pages Status savingIs turned on Sub Menu Page Cable Connection RS-232C SpecificationsSetting Up Ceiling Presenter side DSUB-9PTransmission command PC → Ceiling Presenter Transmission SpecificationsData Format Specifications ConnectionResponse data format Ceiling Presenter→ PC Uart Communication Format Function Replacing the Lamp Replacement of the lamp requires a work done at a highReplacing the Lamp Location. Take care not to cause accidentTroubleshooting Hints Symptoms and ConfirmationRCA pin jack/75 Ω unbalanced NTSC/PAL Video output 11SPECIFICATIONSGeneral Type B receptacleCamera LightingSupplied Accessories Optional parts to be purchased separatelyMemo Overseas Subsidiary Companies