Texas Instruments TLV320AIC3107EVM-K quick start Default Configuration and Connections

www.ti.com EVM Description and Basics

2.2Default Configuration and Connections

2.2.1USB-MODEVM

Table 1 provides a list of the SW2 settings on the USB-MODEVM. For use with the TLV320AIC3107EVM, SW-2 positions 1 through 7 must be set to ON (LO), whereas SW-2.8 must be set to OFF (HI).

	Table 1. USB-MODEVM SW2 Settings
SW-2 Switch Number	Label	Switch Description
1	A0	USB-MODEVM EEPROM I2C Address A0
		ON: A0 = 0
		OFF: A0 = 1
2	A1	USB-MODEVM EEPROM I2C Address A1
		ON: A1 = 0
		OFF: A1 = 1
3	A2	USB-MODEVM EEPROM I2C Address A2
		ON: A2 = 0
		OFF: A2 = 1
4	USB I2S™	I2S Bus Source Selection
		ON: I2S Bus connects to TAS1020
		OFF: I2S Bus connects to USB-MODEVM J14
5	USB MCK	I2S Bus MCLK Source Selection
		ON: MCLK connects to TAS1020
		OFF: MCLK connects to USB-MODEVM J14
6	USB SPI	SPI Bus Source Selection
		ON: SPI Bus connects to TAS1020
		OFF: SPI Bus connects to USB-MODEVM J15
7	USB RST	RST Source Selection
		ON: EVM Reset Signal comes from TAS1020
		OFF: EVM Reset Signal comes from USB-MODEVM J15
8	EXT MCK	External MCLK Selection
		ON: MCLK Signal is provided from USB-MODEVM J10
		OFF: MCLK Signal comes from either selection of SW2-5

2.2.2TLV320AIC3107EVM Jumpers and Switches

Table 2 provides a list of jumpers found on the EVM and their factory default conditions.

			Table 2. List of Stand-alone Jumpers
Jumper	Jumper	Default
Number	Type	Position	Jumper Description
W1	2-pin	soldered	AVDD_ADC power
W2	2-pin	soldered	DRVDD power (DRVDD1 on EVM).
W3	2-pin	soldered	DRVDD power (DRVDD2 on EVM).
W3	2-pin	soldered	AVDD_DAC power.
W5	2-pin	soldered	SPVDD power.
W7	2-pin	soldered	DVDD power.
W8	2-pin	soldered	IOVDD power.
W9	3-pin	2-3	Mic bias select. Connect 1-2 to use AIC3107 Mic Bias. Connect 2-3 to use EVM 3.3V Mic Bias.
W10	2-pin	Open	Connect EVM Onboard Mic to AIC3107 MIC3R input.
W11	2-pin	Open	Connect EVM Onboard Mic to AIC3107 MIC3L input.
W12	2-pin	Open	Enable 16-ohm load for HPL output test.
W13	2-pin	Open	Enable 16-ohm load for HPR output test.
W14	3-pin	1-2	IOVDD select. Connect 1-2 for IOVDD=+1.8V. Connect 2-3 for IOVDD=+3.3V.
W15	2-pin	Open	GPIO1 access point.
W16	2-pin	Installed	Software reset enable.
SLAU261–November 2008			TLV320AIC3107EVM-K	5

Submit Documentation Feedback