Sharp PG-LW2000 appendix System Lock Function, Enter the same keycode in Re- confirm

Page 49

6 System Lock Function

This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest you record the keycode in a safe place where only authorized users have access.

Info

If you lose or forget your keycode, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 69). Even if the product warranty is valid, the keycode reset will incur a charge.

a Setting/Changing the Keycode

1 Select “System Lock”, then press

ENTER or Q.

2Select “Next”, then press ENTER.

The screen for entering the keycode appears.

3Press the 4 buttons on the remote control or on the projector to enter the preset keycode in “Old Code”.

When setting the keycode for the fi rst time, press R on the projector for four times.

 

 

PRJ - ADJ1

 

 

Setting the System Lock

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Old Code

 

 

 

New Code

 

– – – –

 

 

Reconfirm

 

– – – –

 

Note

If you input a wrong keycode, the cursor returns to the fi rst point of the “Old Code”.

The preset keycode is 4 R buttons on the projector. When you press the R button four times, the keycode input screen disappears.

Menu operation n Page 36

4 Press the 4 buttons on the remote control or on the projector to enter the new keycode in “New Code”.

Note

You cannot use the following buttons for keycode: STANDBY/ON, ON,

STANDBY, ENTER, RETURN and

MENU

System Lock function recognizes each button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in setting your keycode, the keycode cannot be canceled with the remote control.

 

 

PRJ - ADJ1

 

 

Setting the System Lock

 

 

 

 

 

 

 

Old Code

* * * *

 

 

New Code

 

 

 

Reconfirm

 

– – – –

5Enter the same keycode in “Re- confirm”.

Note

To cancel the keycode that you have already set

Press R on the projector for four times in steps 4 and 5 above.

When the System Lock is set

When System Lock is set, the keycode input screen appears after the power is turned on. When it appears, enter the right keycode to start projection.

Input screen for keycode

 

 

 

 

 

 

 

 

System Lock

 

 

 

 

 

 

 

 

Features

Useful

47

Image 49
Contents PG-LW2000 Model No Serial No Void the users authority to operate this equipment See bottom of projectorInformation Product Disposal Optional accessories AccessoriesContents Viewing Stereoscopic 3D Images ReferencePower Sources CleaningAccessories Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment 15 16 Part Names and FunctionsRear View Terminals Part Names and Functions Inserting the Batteries Remote control signal transmittersUsable Range Easy Start Setup and ProjectionOn the remote control Correcting trapezoidal distortion using Keystone CorrectionInput list Video Setup Setting Up the ProjectorSetting Up the Projector Standard Setup Front ProjectionScreen Size and Projection Distance Signal Input Normal ModeScreen Lens center Ceiling-Mount Setup Projection PRJ ModeYou may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment AC socket To AC outlet Power cord supplied Connecting the Power CordControlling the Projector by a Computer RS-232C Terminal D-sub 9 pin male connectorTurning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On Adjusting the Projected Image Adjusting the Focus About the Setup GuidePress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Picture Size Adjusting the HeightUse the rear adjustment foot to make the projector level Rotate the zoom ring to enlarge or shrink the picture sizePress Keystone Correcting Trapezoidal DistortionAdjusting the Volume Switching the Input ModeVOL +/- Volume buttons Input buttons AV Mute button Buttons Press Resize Resize ModeButton About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImagePicture menu Menu ItemsMain menu Projector adjustment PRJ-ADJ1/2 menu Menu Selections Quick Start Menu Using the Menu ScreenPress Menu ExampleQuick Start Menu Example Adjusting BrightMenu Selections Complete Menu Following items can be configured on the Quick Start MenuPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press EnterSelecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting the Color Temperature Adjusting the ImageAdjusting the Colors Adjusting Hue, Saturation, or ValueEco+Quiet Selecting the Film ModeReducing Image Noise DNR Resolution Setting Signal Adjustment SIG-ADJ MenuSignal Type Setting Setting the Video Setup Setting the Video SystemChecking the Input Signal When reproducing Ntsc signals in PAL video equipmentSetting the Resize Mode Adjusting the Projected Image SCR-ADJ MenuAdjusting the Image Position Keystone CorrectionSetting the On-screen Display Setting the OverscanClosed Caption For Americas onlySelecting the Background Image Selecting the Setup GuideReversing/Inverting Projected Images Selecting the Wall ColorAuto Power Off Function Auto Sync Auto Sync AdjustmentSpeaker Setting Fan Mode SettingWhen the System Lock is set To cancel the keycode that you have already setSystem Lock Function Enter the same keycode in Re- confirmKeylock Function Adjusting the Projector Function PRJ-ADJ1/2 MenuTaking the Keylock Off Select On, then press EnterStandby Mode Setting the Function Button OperationReturning to the Default Settings Selecting the Quick Start MenuViewing Stereoscopic 3D Images Precautions on Viewing Stereoscopic 3D ImagesInformation on the 3D Projection Function Shutter glasses control light signalAppendix Projecting 3D images Using 3D Viewing ModeEnding 3D projection Cleaning the projector MaintenanceAbout the temperature warning indicator Maintenance IndicatorsAbnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitSTANDBY/ON button AC socket Resetting the Lamp Timer Computer control RS-232C Specifications and CommandsCommunication conditions Basic formatComputer Projector CommandsRGB PAL CC1 Computer Compatibility ChartDTV 19-22 Troubleshooting53, 54 Problem Check Sharp Electronics France For Sharp AssistanceSpecifications Units inches mm DimensionsIndex
Related manuals
Manual 75 pages 35.4 Kb