Sharp PG-LW2000 appendix Regarding the Lamp, Replacing the Lamp

Page 58

Regarding the Lamp

Lamp

■It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page 49.)

■Purchase a replacement lamp of type AN-LX20LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information

www.lamprecycle.org or 1-800-BE-SHARP

U.S.A ONLY

Caution Concerning the Lamp

■This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.

■Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

Caution

•Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury.

•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

■Carefully change the lamp by following the instructions described in this section.

* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

*If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair.

56

Page 57 Page 59
Image 58
Page 57 Page 59
Contents PG-LW2000 Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Accessories Optional accessoriesContents Reference Viewing Stereoscopic 3D ImagesAccessories CleaningPower Sources Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Part Names and Functions 15 16Rear View Terminals Part Names and Functions Inserting the Batteries Remote control signal transmittersUsable Range Setup and Projection Easy StartOn the remote control Correcting trapezoidal distortion using Keystone CorrectionInput list Setting Up the Projector Setting Up the ProjectorVideo Setup Standard Setup Front ProjectionScreen Size and Projection Distance Signal Input Normal ModeScreen Lens center Projection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment Connecting the Power Cord AC socket To AC outlet Power cord suppliedRS-232C Terminal D-sub 9 pin male connector Controlling the Projector by a ComputerTurning the Projector On/Off Power indicator Lamp indicatorTurning the Projector On Press Enter to exit the Setup Guide screen About the Setup GuideAdjusting the Projected Image Adjusting the Focus Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightAdjusting the Picture Size Rotate the zoom ring to enlarge or shrink the picture sizeCorrecting Trapezoidal Distortion Press KeystoneAdjusting the Volume Switching the Input ModeVOL +/- Volume buttons Input buttons AV Mute button Buttons Press Resize Resize ModeButton About Copyrights Using the Spot Function Operating with the Remote ControlDisplaying and Setting the Break Timer Switching the Eco+Quiet ModeFreezing a Moving Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Displaying an Enlarged Portion of an ImageMenu Items Picture menuMain menu Projector adjustment PRJ-ADJ1/2 menu Press Menu Using the Menu ScreenMenu Selections Quick Start Menu ExampleMenu Selections Complete Menu Example Adjusting BrightQuick Start Menu Following items can be configured on the Quick Start MenuPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press EnterSelecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting the Colors Adjusting the ImageAdjusting the Color Temperature Adjusting Hue, Saturation, or ValueEco+Quiet Selecting the Film ModeReducing Image Noise DNR Resolution Setting Signal Adjustment SIG-ADJ MenuSignal Type Setting Checking the Input Signal Setting the Video SystemSetting the Video Setup When reproducing Ntsc signals in PAL video equipmentAdjusting the Image Position Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Keystone CorrectionClosed Caption Setting the OverscanSetting the On-screen Display For Americas onlyReversing/Inverting Projected Images Selecting the Setup GuideSelecting the Background Image Selecting the Wall ColorSpeaker Setting Auto Sync Auto Sync AdjustmentAuto Power Off Function Fan Mode SettingSystem Lock Function To cancel the keycode that you have already setWhen the System Lock is set Enter the same keycode in Re- confirmTaking the Keylock Off Adjusting the Projector Function PRJ-ADJ1/2 MenuKeylock Function Select On, then press EnterReturning to the Default Settings Setting the Function Button OperationStandby Mode Selecting the Quick Start MenuPrecautions on Viewing Stereoscopic 3D Images Viewing Stereoscopic 3D ImagesInformation on the 3D Projection Function Shutter glasses control light signalAppendix Projecting 3D images Using 3D Viewing ModeEnding 3D projection Maintenance Cleaning the projectorMaintenance Indicators About the temperature warning indicatorAbnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitSTANDBY/ON button AC socket Resetting the Lamp Timer Communication conditions RS-232C Specifications and CommandsComputer control Basic formatCommands Computer ProjectorRGB PAL CC1 Compatibility Chart ComputerDTV Troubleshooting 19-2253, 54 Problem Check For Sharp Assistance Sharp Electronics FranceSpecifications Dimensions Units inches mmIndex
Related manuals
Manual 75 pages 35.4 Kb
Top Page Image Contents