Sharp PG-LW2000 appendix Resetting the Lamp Timer

Page 60

Regarding the Lamp (Continued)

	4 Remove the lamp unit.	Securing
	• Loosen the securing screw from the lamp	screw
	unit. Hold the lamp unit and pull it in the	screw
	unit. Hold the lamp unit and pull it in the
	direction of the arrow. At this time, keep
	the lamp unit horizontal and do not tilt it.

5 Insert the new lamp unit.

• Press the lamp unit ﬁ rmly into the lamp unit compartment to align the lamp connectors. Fasten the securing screw.

6 Replace the lamp unit cover.

• Slide the lamp unit cover horizontally back into place and align the tabs (1). Then tighten the user service screw (2) to secure the lamp unit cover.

Info

• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

1 Connect the power cord.	AC socket
• Plug the power cord into the AC socket of
the projector.

2 Reset the lamp timer.

• While simultaneously holding down MENU, ENTER and R on the projector, press STANDBY/ON on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green.

•“LAMP 0000H” is displayed, indicating that the lamp timer is reset.

STANDBY/ON button

ENTER button

MENU button

Rbutton

58

Image 60

Contents PG-LW2000 Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Accessories Optional accessoriesContents Reference Viewing Stereoscopic 3D ImagesCleaning Power SourcesAccessories Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Part Names and Functions 15 16Rear View Terminals Part Names and Functions Remote control signal transmitters Inserting the BatteriesUsable Range Setup and Projection Easy StartCorrecting trapezoidal distortion using Keystone Correction On the remote controlInput list Setting Up the Projector Video SetupSetting Up the Projector Standard Setup Front ProjectionSignal Input Normal Mode Screen Size and Projection DistanceScreen Lens center Projection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment Connecting the Power Cord AC socket To AC outlet Power cord suppliedRS-232C Terminal D-sub 9 pin male connector Controlling the Projector by a ComputerPower indicator Lamp indicator Turning the Projector On/OffTurning the Projector On About the Setup Guide Adjusting the Projected Image Adjusting the FocusPress Enter to exit the Setup Guide screen Image ProjectionAdjusting the Height Adjusting the Picture SizeUse the rear adjustment foot to make the projector level Rotate the zoom ring to enlarge or shrink the picture sizeCorrecting Trapezoidal Distortion Press KeystoneSwitching the Input Mode Adjusting the VolumeVOL +/- Volume buttons Input buttons AV Mute button Buttons Resize Mode Press ResizeButton About Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageMenu Items Picture menuMain menu Projector adjustment PRJ-ADJ1/2 menu Using the Menu Screen Menu Selections Quick Start MenuPress Menu ExampleExample Adjusting Bright Quick Start MenuMenu Selections Complete Menu Following items can be conﬁgured on the Quick Start MenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press EnterPicture Adjustment Picture Menu Selecting the Picture ModeMenu operation n Adjusting the Image Adjusting the Color TemperatureAdjusting the Colors Adjusting Hue, Saturation, or ValueSelecting the Film Mode Eco+QuietReducing Image Noise DNR Signal Adjustment SIG-ADJ Menu Resolution SettingSignal Type Setting Setting the Video System Setting the Video SetupChecking the Input Signal When reproducing Ntsc signals in PAL video equipmentAdjusting the Projected Image SCR-ADJ Menu Setting the Resize ModeAdjusting the Image Position Keystone CorrectionSetting the Overscan Setting the On-screen DisplayClosed Caption For Americas onlySelecting the Setup Guide Selecting the Background ImageReversing/Inverting Projected Images Selecting the Wall ColorAuto Sync Auto Sync Adjustment Auto Power Off FunctionSpeaker Setting Fan Mode SettingTo cancel the keycode that you have already set When the System Lock is setSystem Lock Function Enter the same keycode in Re- conﬁrmAdjusting the Projector Function PRJ-ADJ1/2 Menu Keylock FunctionTaking the Keylock Off Select On, then press EnterSetting the Function Button Operation Standby ModeReturning to the Default Settings Selecting the Quick Start MenuPrecautions on Viewing Stereoscopic 3D Images Viewing Stereoscopic 3D ImagesShutter glasses control light signal Information on the 3D Projection FunctionAppendix Using 3D Viewing Mode Projecting 3D imagesEnding 3D projection Maintenance Cleaning the projectorMaintenance Indicators About the temperature warning indicatorAbnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Remove the lamp unit coverSTANDBY/ON button AC socket Resetting the Lamp Timer RS-232C Speciﬁcations and Commands Computer controlCommunication conditions Basic formatCommands Computer ProjectorRGB PAL CC1 Compatibility Chart ComputerDTV Troubleshooting 19-2253, 54 Problem Check For Sharp Assistance Sharp Electronics FranceSpeciﬁcations Dimensions Units inches mmIndex

Related manuals

Manual 75 pages 35.4 Kb