Sharp XV-Z3000U operation manual Introduction

Page 2
U.S.A. ONLY

Before using the projector, please read this operation manual carefully.

Introduction

IMPORTANT

For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information.

Before recycling the packaging, please ensure that you have checked the con- tents of the carton thoroughly against the list of “Supplied accessories” on page 10.

Model No.: XV-Z3000U

Serial No.:

ENGLISH

There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.

1.WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2.CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection,

modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT

“LIMITED WARRANTY” CLAUSE.

U.S.A. ONLY

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead sym- bol, within an equilateral triangle, is in- tended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

1

Image 2
Contents XV-Z3000U Introduction Information For Future Reference IntroductionContents Maintenance Maintenance Indicators Regarding the Lamp ReferenceAccessories CleaningPower Sources Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingDo not block the exhaust and intake vents Rest your eyes occasionallyAvoid locations with extremes of tem- perature Potential hazard of glass parOther connected equipment Using the projector in other countriesTemperature monitor function Accessories Optional accessoriesPart Names and Functions Power IndicatorFocus ring For adjusting the focus ProjectorPart Names and Functions Rear ViewUsing the Kensington Lock on the projector Inserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range Setup and Projection Quick StartAdjust the focus, image size, and projector angle PP Standard Setup Front Projection Setting up the ProjectorSetting up the Projector Ceiling-mount SetupProjection Projection PRJ Mode174× DistancePicture Screen Size and Projection Distance Setting up the ProjectorWhen using a wide screen 169 and projecting 169 image When using a normal screen 43 and projecting 169 image Samples of Cables for Connection Connecting to Video Equipment Connecting to Video Equipment When connecting to equipment with Hdmi output teminal INPUT6 To INPUT5 terminal RGB cable commercially available Connecting to a ComputerComputer To RGB output terminal Controlling the Projector by a Computer Turning the Projector On/Off Connecting the Power CordLamp indicator Power indicator STANDBY/ON button On button Turning the Projector onImage Projection Switching the Input ModeUnplug the power cord from the AC Outlet after the cooling fan stopsImage Projection Adjusting the Projected ImageAdjust lever Make small adjustments Rotate the zoom ring to enlarge or shrink the screen sizeUse the rear adjustment foot to make the projector level Correcting Trapezoidal Distortion Designating the corner Display disappearsFor correcting an image by Projected imagePress i Enter to set the posi- tion ROn-screen displayKeystone Resize Mode On the projector On the remote control Resize buttonAbout Copyrights ComputerSelecting the Picture Mode Operating with the Remote ControlSwitching the Iris Setting Shifting the Projected Im- age Vertically Image ShiftMenu Items Picture menuMenu Items Fine Sync menuPress Q or O to select the menu icon to adjust Using the Menu ScreenMenu Selections Adjustments Press dMENUPress P or R to select the item to adjust Using the Menu ScreenTo adjust the projected image while watching it Press O or Q to adjust the item selected2Adjusting the Image Picture Adjustment Picture menu1Selecting the Picture Mode Menu operation n4Adjusting the Colors Picture Adjustment Picture menu3Adjusting the Color Temperature Progressive8Lamp Setting 6Reducing Image Noise 7Switching the IrisSetting 3Auto Sync Auto Sync Adjustment 1Adjusting Computer Image2Special Modes Setting 4Checking the Input Signal1Adjusting the Image Position Using the Options Menu2Adjusting the Overscan You can move the projected image verticallyUsing the Options Menu Reversing/Inverting Projected Images 9Auto Power Off Function0Checking the Lamp Life Status 6Selecting the On-screen Display Language 4Fan Mode Setting5Returning to the Default Settings This function changes the fan rotation speedMaintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer Regarding the LampConnecting Pin Assignments GNDReturn code 0DH RS-232C Specifications and Command SettingsConnecting Pin Assignments R Return code 0DHComputer Compatibility Chart Vesa HdmiTroubleshooting 23-27Service Information For the U.S Specifications Product type Projector Model XV-Z3000 Video systemDimensions Index Appendix