Sharp XV-Z3000U operation manual Removing and Installing the Lamp Unit, Disconnect the power cord

Page 56

Removing and Installing the Lamp Unit

Warning!

•The lamp unit becomes very hot while the pro- jector is operating. Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Optional	Lamp unit
accessory	AN-100LP

Info

•Make sure that you remove the lamp unit by the handle. Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1Press SSTANDBY/ON on the pro- jector or aSTANDBY on the re- mote control to put the projector into standby mode.

•Wait until the cooling fan stops.

2Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3Remove the lamp unit cover.

•Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

STANDBY/ON button

AC socket

1

2

User service screw (for lamp unit cover)

Appendix

55

Image 56

Contents XV-Z3000U Introduction Information For Future Reference IntroductionContents Maintenance Maintenance Indicators Regarding the Lamp ReferenceCleaning Power SourcesAccessories Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Potential hazard of glass parOther connected equipment Using the projector in other countriesTemperature monitor function Accessories Optional accessoriesPower Indicator Focus ring For adjusting the focusPart Names and Functions ProjectorPart Names and Functions Rear ViewUsing the Kensington Lock on the projector Inserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range Setup and Projection Quick StartAdjust the focus, image size, and projector angle PP Setting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode 174×Projection DistancePicture Screen Size and Projection Distance Setting up the ProjectorWhen using a wide screen 169 and projecting 169 image When using a normal screen 43 and projecting 169 image Samples of Cables for Connection Connecting to Video Equipment Connecting to Video Equipment When connecting to equipment with Hdmi output teminal INPUT6 To INPUT5 terminal RGB cable commercially available Connecting to a ComputerComputer To RGB output terminal Controlling the Projector by a Computer Connecting the Power Cord Lamp indicator Power indicator STANDBY/ON button On buttonTurning the Projector On/Off Turning the Projector onSwitching the Input Mode Unplug the power cord from the ACImage Projection Outlet after the cooling fan stopsAdjusting the Projected Image Adjust lever Make small adjustmentsImage Projection Rotate the zoom ring to enlarge or shrink the screen sizeUse the rear adjustment foot to make the projector level Correcting Trapezoidal Distortion Display disappears For correcting an image byDesignating the corner Projected imagePress i Enter to set the posi- tion ROn-screen displayKeystone Resize Mode On the projector On the remote control Resize buttonAbout Copyrights ComputerOperating with the Remote Control Switching the Iris SettingSelecting the Picture Mode Shifting the Projected Im- age Vertically Image ShiftMenu Items Picture menuMenu Items Fine Sync menuUsing the Menu Screen Menu Selections AdjustmentsPress Q or O to select the menu icon to adjust Press dMENUUsing the Menu Screen To adjust the projected image while watching itPress P or R to select the item to adjust Press O or Q to adjust the item selectedPicture Adjustment Picture menu 1Selecting the Picture Mode2Adjusting the Image Menu operation nPicture Adjustment Picture menu 3Adjusting the Color Temperature4Adjusting the Colors Progressive8Lamp Setting 6Reducing Image Noise 7Switching the IrisSetting 1Adjusting Computer Image 2Special Modes Setting3Auto Sync Auto Sync Adjustment 4Checking the Input SignalUsing the Options Menu 2Adjusting the Overscan1Adjusting the Image Position You can move the projected image verticallyUsing the Options Menu Reversing/Inverting Projected Images 9Auto Power Off Function0Checking the Lamp Life Status 4Fan Mode Setting 5Returning to the Default Settings6Selecting the On-screen Display Language This function changes the fan rotation speedMaintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer Regarding the LampConnecting Pin Assignments GNDRS-232C Specifications and Command Settings Connecting Pin AssignmentsReturn code 0DH R Return code 0DHComputer Compatibility Chart Vesa HdmiTroubleshooting 23-27Service Information For the U.S Specifications Product type Projector Model XV-Z3000 Video systemDimensions Index Appendix