Sharp XV-Z3000U operation manual Regarding the Lamp, Replacing the Lamp

Page 55

Regarding the Lamp

Lamp

■It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (see page 49)

■Purchase a replacement lamp of type AN-100LP from your place of purchase, nearest Authorized SharpVision Service Center or Dealer.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through an Authorized SharpVision Service Center or Dealer. For the name of the nearest Authorized SharpVision Service Center or Dealer, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information

www.lamprecycle.org or 1-800-BE-SHARP

U.S.A. ONLY

 

 

 

Caution Concerning the Lamp

■This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time.

The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Authorized SharpVision Service Center or Dealer to assure safe operation.

■Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

•Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury.

■Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Authorized SharpVision Service Center or Dealer.

*If the new lamp does not light after replacement, take your projector to the nearest Authorized SharpVision Service Center or Dealer for repair.

54

Page 54 Page 56
Image 55
Page 54 Page 56
Contents XV-Z3000U Introduction Information Introduction For Future ReferenceContents Reference Maintenance Maintenance Indicators Regarding the LampPower-Cord Protection CleaningPower Sources AccessoriesOverloading Damage Requiring ServiceReplacement Parts Safety CheckPotential hazard of glass par Rest your eyes occasionallyAvoid locations with extremes of tem- perature Do not block the exhaust and intake ventsTemperature monitor function Using the projector in other countriesOther connected equipment Optional accessories AccessoriesProjector Power IndicatorFocus ring For adjusting the focus Part Names and FunctionsRear View Part Names and FunctionsUsing the Kensington Lock on the projector Attach the cover and slide it until it clicks into place Inserting the BatteriesUsable Range Quick Start Setup and ProjectionAdjust the focus, image size, and projector angle PP Ceiling-mount Setup Setting up the ProjectorSetting up the Projector Standard Setup Front ProjectionDistance Projection PRJ Mode174× ProjectionWhen using a wide screen 169 and projecting 169 image Setting up the ProjectorPicture Screen Size and Projection Distance When using a normal screen 43 and projecting 169 image Samples of Cables for Connection Connecting to Video Equipment Connecting to Video Equipment When connecting to equipment with Hdmi output teminal INPUT6 Computer To RGB output terminal Connecting to a ComputerTo INPUT5 terminal RGB cable commercially available Controlling the Projector by a Computer Turning the Projector on Connecting the Power CordLamp indicator Power indicator STANDBY/ON button On button Turning the Projector On/OffOutlet after the cooling fan stops Switching the Input ModeUnplug the power cord from the AC Image ProjectionRotate the zoom ring to enlarge or shrink the screen size Adjusting the Projected ImageAdjust lever Make small adjustments Image ProjectionUse the rear adjustment foot to make the projector level Correcting Trapezoidal Distortion Projected image Display disappearsFor correcting an image by Designating the cornerROn-screen display Press i Enter to set the posi- tionKeystone On the projector On the remote control Resize button Resize ModeComputer About CopyrightsShifting the Projected Im- age Vertically Image Shift Operating with the Remote ControlSwitching the Iris Setting Selecting the Picture ModePicture menu Menu ItemsFine Sync menu Menu ItemsPress dMENU Using the Menu ScreenMenu Selections Adjustments Press Q or O to select the menu icon to adjustPress O or Q to adjust the item selected Using the Menu ScreenTo adjust the projected image while watching it Press P or R to select the item to adjustMenu operation n Picture Adjustment Picture menu1Selecting the Picture Mode 2Adjusting the ImageProgressive Picture Adjustment Picture menu3Adjusting the Color Temperature 4Adjusting the ColorsSetting 6Reducing Image Noise 7Switching the Iris8Lamp Setting 4Checking the Input Signal 1Adjusting Computer Image2Special Modes Setting 3Auto Sync Auto Sync AdjustmentYou can move the projected image vertically Using the Options Menu2Adjusting the Overscan 1Adjusting the Image PositionUsing the Options Menu 0Checking the Lamp Life Status 9Auto Power Off FunctionReversing/Inverting Projected Images This function changes the fan rotation speed 4Fan Mode Setting5Returning to the Default Settings 6Selecting the On-screen Display LanguageCleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Regarding the Lamp Resetting the Lamp TimerGND Connecting Pin AssignmentsR Return code 0DH RS-232C Specifications and Command SettingsConnecting Pin Assignments Return code 0DHVesa Hdmi Computer Compatibility Chart23-27 TroubleshootingService Information For the U.S Product type Projector Model XV-Z3000 Video system SpecificationsDimensions Index Appendix
Top Page Image Contents