Sharp XV-Z3000U Turning the Projector On/Off, Connecting the Power Cord, Turning the Projector on

Page 29

Turning the Projector On/Off

Connecting the Power Cord

	Supplied	Power cord
	accessory	Power cord
	accessory

Plug the supplied power cord into the AC socket on the rear of the projector.

AC socket

Turning the Projector on

Note that the connections to external equip- ment and power outlet should be done be- fore performing the operations written be- low. (See pages 23 to 28.)

Remove the lens cap and press SSTANDBY/ON on the projector or bON on the remote control.

Note

•About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on.

Blinking in green: The lamp is warming up

or shutting down.

Red:The lamp is shut down abnormally or the lamp should be replaced.

•When switching on the projector, a slight flick- ering of the image may be experienced within the first minute after the lamp has been illumi- nated. This is normal operation as the lamp’s control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.

•If the projector is put into standby mode and immediately turned on again, the lamp may take some time to start projection.

Info

•English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 50.

Lamp indicator

Power indicator

STANDBY/ON button

ON button

28

Image 29

Contents XV-Z3000U Introduction Information Introduction For Future ReferenceContents Reference Maintenance Maintenance Indicators Regarding the LampPower Sources CleaningAccessories Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingAvoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the exhaust and intake vents Potential hazard of glass parOther connected equipment Using the projector in other countriesTemperature monitor function Optional accessories AccessoriesFocus ring For adjusting the focus Power IndicatorPart Names and Functions ProjectorRear View Part Names and FunctionsUsing the Kensington Lock on the projector Attach the cover and slide it until it clicks into place Inserting the BatteriesUsable Range Quick Start Setup and ProjectionAdjust the focus, image size, and projector angle PP Setting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount Setup174× Projection PRJ ModeProjection DistancePicture Screen Size and Projection Distance Setting up the ProjectorWhen using a wide screen 169 and projecting 169 image When using a normal screen 43 and projecting 169 image Samples of Cables for Connection Connecting to Video Equipment Connecting to Video Equipment When connecting to equipment with Hdmi output teminal INPUT6 To INPUT5 terminal RGB cable commercially available Connecting to a ComputerComputer To RGB output terminal Controlling the Projector by a Computer Lamp indicator Power indicator STANDBY/ON button On button Connecting the Power CordTurning the Projector On/Off Turning the Projector onUnplug the power cord from the AC Switching the Input ModeImage Projection Outlet after the cooling fan stopsAdjust lever Make small adjustments Adjusting the Projected ImageImage Projection Rotate the zoom ring to enlarge or shrink the screen sizeUse the rear adjustment foot to make the projector level Correcting Trapezoidal Distortion For correcting an image by Display disappearsDesignating the corner Projected imageROn-screen display Press i Enter to set the posi- tionKeystone On the projector On the remote control Resize button Resize ModeComputer About CopyrightsSwitching the Iris Setting Operating with the Remote ControlSelecting the Picture Mode Shifting the Projected Im- age Vertically Image ShiftPicture menu Menu ItemsFine Sync menu Menu ItemsMenu Selections Adjustments Using the Menu ScreenPress Q or O to select the menu icon to adjust Press dMENUTo adjust the projected image while watching it Using the Menu ScreenPress P or R to select the item to adjust Press O or Q to adjust the item selected1Selecting the Picture Mode Picture Adjustment Picture menu2Adjusting the Image Menu operation n3Adjusting the Color Temperature Picture Adjustment Picture menu4Adjusting the Colors Progressive8Lamp Setting 6Reducing Image Noise 7Switching the IrisSetting 2Special Modes Setting 1Adjusting Computer Image3Auto Sync Auto Sync Adjustment 4Checking the Input Signal2Adjusting the Overscan Using the Options Menu1Adjusting the Image Position You can move the projected image verticallyUsing the Options Menu Reversing/Inverting Projected Images 9Auto Power Off Function0Checking the Lamp Life Status 5Returning to the Default Settings 4Fan Mode Setting6Selecting the On-screen Display Language This function changes the fan rotation speedCleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Regarding the Lamp Resetting the Lamp TimerGND Connecting Pin AssignmentsConnecting Pin Assignments RS-232C Specifications and Command SettingsReturn code 0DH R Return code 0DHVesa Hdmi Computer Compatibility Chart23-27 TroubleshootingService Information For the U.S Product type Projector Model XV-Z3000 Video system SpecificationsDimensions Index Appendix