Sharp AR-162, AR-163 Copier Installation, Do not install your copier in areas that are

Page 10

GETTING STARTED Copier installation

COPIER INSTALLATION

Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved.

If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.

Do not install your copier in areas that are:

●damp, humid, or very dusty

● exposed to direct sunlight

●poorly ventilated

●subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.

The copier should be installed near an accessible power outlet for easy connection.

Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded.

●For this copier’s power supply requirements, see the name plate located on the back of the unit.

Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine for servicing and proper ventilation.

10 cm (4")

8

Image 10

Contents AR-163 Follow the cautions below when using this copier Contents Conventions used in this manual IntroductionAB series metric and inch series references Main Features Part Names and Functions Part Names and Functions Paper Size indicators Interrupt key and indicator pZoom indicator p.17 Alarm indicatorsOriginal Size Enter key and indicators p Start key and indicatorPreset Ratio selector keys and indicators p Auto Paper Select indicatorCopier Installation Do not install your copier in areas that areDo not touch the photoconductive drum green portion Gently lift and pull out the paper tray until it stops Loading Copy PaperPush the paper tray firmly back into the copier Loading Copy Paper Key Press the Start key and then the Paper Size Enter keyWhen copying is completed, press the Audit Clear Key Enter your account number using the numeric keysAuditing Accounts Adjust the copy density Turn the power switch onNormal Copying Normal Copying How to remove the platen coverSet the number of copies using the numeric keys Press the Start keyPress the Auto Image Key REDUCTION/ENLARGEMENT/ZOOMAutomatic Enter the number of copies Press the Start keyManual REDUCTION/ENLARGEMENT/ZOOMSet the number of copies and press the Start key Bypass Feed special paper Unfold the bypass trayBypass Feed special paper TWO-SIDED Copying Press the XY-ZOOM key XY ZoomPress the copy ratio display key XY Zoom Use the Preset Ratio selector , keys and zoomEnter the desired number of copies Press the Start key Reverse Press the B/W Reverse key Check the copy paper sizePress the Dual page Copy key Dual page CopySet the number of copies Press the Start key Interrupting a Copy RUN When all Interrupt copies are finished, pressPress the Interrupt key Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light keyFive times Toner cartridge out. Remove the toner cartridge whileRemove the new toner cartridge from the bag. Hold Push the toner cartridge lock release lever and pullToner cartridge life Toner Cartridge ReplacementPress the light key Misfeed in the copier Misfeed RemovalMisfeed in the bypass tray First confirm the misfeed locationMisfeed Removal Turn the roller rotating knob in the direction Arrow Misfeed in the paper tray Close the side cover by pressing the handle on CoverMaintenance Required Developer RequiredList of user programs User ProgramsProgram No Program name Description User Programs Setting the user programsEnter a program number using the numeric keys Program name Program NoSelect the desired parameter using the numeric keys OFFSelect the desired setting using the numeric keys Settings for auditing accountsEnter a 3-digit account number using the numeric keys Program No Account number change Use the copy ratio display key to select the account Number Press and hold down the 0 keyProgram No Resetting account Preheat mode Power Save ModesAuto power shut-off mode Copying from the preheat mode Power Save ModesSetting the power save modes Copying from the auto power shut-off modeOriginal table and platen cover User MaintenanceBypass tray paper feed roller Transfer charger cleaning User MaintenanceCharger cleaner out by holding the tab Problem Solution Copier TROUBLE?Copier TROUBLE? COPY/FAX keySelf-diagnostic function ExampleSupplies Types and sizes of copy paperProper storage SuppliesGenuine supplies statement Store the supplies in a location that isSpecifications Specifications Optional Equipment System Configuration Single Pass Feeder AR-SP2 SpecificationsPart Names Using the SPF Single Pass Feeder AR-SP2Misfeed removal Electronic Sorting KIT AR-EB3 Rotation copyingElectronic Sorting KIT AR-EB3 Sort modeGroup mode Sort/groupCopying in the sort mode Set the originals face up in the document feeder tray1 or 4 Selection Enter the desired pattern number using a numeric keyPress the 2 in 1 / 4 Key to completePress the Erase / key to select the desired Erase mode EraseElectronic Sorting KIT AR-EB3 Margin shift Press the Margin Shift key Check the copy paper sizeSheet Paper Feed Unit AR-DE5 Loading copy paperConfirm that the misfeed indicator has gone out AR-DE5 Index Index Material Safety Data Sheet Flash Point Method Used Ignition TemperatureSpecial Fire Fighting Procedure Flammable LimitsOther Limits Ingredients CAS No ProportionMedical Conditions Generally Aggravated by Exposure None required under normal use Memo Class Laser Product Laser Klasse Page Sharp Corporation