Sharp AR-163 Power Save Modes, Setting the power save modes, Copying from the preheat mode

Page 45

POWER SAVE MODES

Setting the power save modes

The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode. For these settings, see page 36.

●The copier will enter the preheat mode first and then the auto power shut-off mode after a preset time has elapsed when no copier operation has been made.

●If conflicting settings are made with user programs No. 3 and No. 5, the last program set will have priority.

Copying from the preheat mode

Make desired copier selections and press the START () key using the normal copying procedure.

●When any key input is made or any other copier operation is made, the POWER SAVE () indicator will start to blink.

●When the START key is pressed, the START key () indicator will go out and copying will start within 10 seconds. The POWER SAVE () indicator will go out when copying starts.

Copying from the auto power shut-off mode

1	Press the START ( ) key.
	● The copier will exit the auto power shut-off mode and the POWER

SAVE () indicator will start to blink.

Make desired copier selections and press the START

2 () key using the normal copying procedure.

●It will take approximately 35 seconds for the copier to start copying.

However, you can make desired settings and press the START () key during warm-up. Copying will start after warm-up is finished.

GENERAL INFORMATION Power save modes

43

Image 45

Contents AR-163 Follow the cautions below when using this copier Contents Introduction Conventions used in this manualAB series metric and inch series references Main Features Part Names and Functions Part Names and Functions Zoom indicator p.17 Interrupt key and indicator pPaper Size indicators Alarm indicatorsPreset Ratio selector keys and indicators p Start key and indicatorOriginal Size Enter key and indicators p Auto Paper Select indicatorDo not install your copier in areas that are Copier InstallationDo not touch the photoconductive drum green portion Loading Copy Paper Gently lift and pull out the paper tray until it stopsPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter key KeyEnter your account number using the numeric keys When copying is completed, press the Audit Clear KeyAuditing Accounts Turn the power switch on Adjust the copy densityNormal Copying Set the number of copies using the numeric keys How to remove the platen coverNormal Copying Press the Start keyAutomatic REDUCTION/ENLARGEMENT/ZOOMPress the Auto Image Key Enter the number of copies Press the Start keyREDUCTION/ENLARGEMENT/ZOOM ManualSet the number of copies and press the Start key Unfold the bypass tray Bypass Feed special paperBypass Feed special paper TWO-SIDED Copying XY Zoom Press the XY-ZOOM keyPress the copy ratio display key Use the Preset Ratio selector , keys and zoom XY ZoomEnter the desired number of copies Press the Start key Press the B/W Reverse key Check the copy paper size ReverseDual page Copy Press the Dual page Copy keySet the number of copies Press the Start key When all Interrupt copies are finished, press Interrupting a Copy RUNPress the Interrupt key Automatic Exposure Adjustment To enter the toner save mode, press the light key Toner Save ModeRemove the new toner cartridge from the bag. Hold Toner cartridge out. Remove the toner cartridge whileFive times Push the toner cartridge lock release lever and pullToner Cartridge Replacement Toner cartridge lifePress the light key Misfeed in the bypass tray Misfeed RemovalMisfeed in the copier First confirm the misfeed locationMisfeed Removal Turn the roller rotating knob in the direction Arrow Close the side cover by pressing the handle on Cover Misfeed in the paper trayDeveloper Required Maintenance RequiredUser Programs List of user programsProgram No Program name Description Enter a program number using the numeric keys Setting the user programsUser Programs Program name Program NoOFF Select the desired parameter using the numeric keysSettings for auditing accounts Select the desired setting using the numeric keysEnter a 3-digit account number using the numeric keys Program No Account number change Press and hold down the 0 key Use the copy ratio display key to select the account NumberProgram No Resetting account Power Save Modes Preheat modeAuto power shut-off mode Setting the power save modes Power Save ModesCopying from the preheat mode Copying from the auto power shut-off modeUser Maintenance Original table and platen coverBypass tray paper feed roller User Maintenance Transfer charger cleaningCharger cleaner out by holding the tab Copier TROUBLE? Problem SolutionCOPY/FAX key Copier TROUBLE?Example Self-diagnostic functionTypes and sizes of copy paper SuppliesGenuine supplies statement SuppliesProper storage Store the supplies in a location that isSpecifications Specifications Optional Equipment System Configuration Specifications Single Pass Feeder AR-SP2Part Names Single Pass Feeder AR-SP2 Using the SPFMisfeed removal Rotation copying Electronic Sorting KIT AR-EB3Group mode Sort modeElectronic Sorting KIT AR-EB3 Sort/groupSet the originals face up in the document feeder tray Copying in the sort mode1 or 4 Press the 2 in 1 / 4 Enter the desired pattern number using a numeric keySelection Key to completeErase Press the Erase / key to select the desired Erase modeElectronic Sorting KIT AR-EB3 Press the Margin Shift key Check the copy paper size Margin shiftLoading copy paper Sheet Paper Feed Unit AR-DE5Confirm that the misfeed indicator has gone out AR-DE5 Index Index Material Safety Data Sheet Special Fire Fighting Procedure Ignition TemperatureFlash Point Method Used Flammable LimitsIngredients CAS No Proportion Other LimitsMedical Conditions Generally Aggravated by Exposure None required under normal use Memo Class Laser Product Laser Klasse Page Sharp Corporation