Sharp XG-MB65X operation manual This Apparatus Must be Earthed

Page 2

IMPORTANT

•For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information.

•Before recycling the packaging, please ensure that you have checked the con- tents of the carton thoroughly against the list of “Supplied accessories” on page 10.

Model No.:

Serial No.:

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat- ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used.

Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.

In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi- ately and disposed of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the instructions below:

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code: Green-and-yellow : Earth

Blue	: Neutral
Brown	: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

•The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.

•The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

•The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

ii

Image 2

Contents XG-MB65X This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianIii Page IntroductionENGLISH A. onlySharp PROJECTOR, Model XG-MB65X Sharp Electronics CorporationUsing the Menu Screen For Future ReferenceContents Reference Power Sources CleaningAccessories Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingDo not block the exhaust and intake vents Rest your eyes occasionallyAvoid locations with extremes of tem- perature Other connected equipment Using the projector in other countriesTemperature monitor function Accessories Optional accessoriesProjector Height 29 AdjustPart Names and Functions Audio Input Rear ViewAudio Input 1 Break Timer Picture ModeInserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range Height Setup and ProjectionQuick Start Upper side ProjectorStandard Setup Front Projection Setting up the ProjectorSetting up the Projector Ceiling-mount SetupProjection Projection PRJ ModeExample Normal Mode Picture Size DistanceScreen Size and Projection Distance Normal ModeStretch Mode COMPUTER-RGB/COMPONENT ConnectionsInput Terminals and Connectable Main Equipment Samples of Cables for Connection Computer To INPUT1 terminal To Audio Terminal Connecting to a ComputerTo audio output terminal To RGB output terminal Connecting to Video Equipment When using an S-video cable INPUT3Connecting to a Monitor with RGB Input Terminal When using a composite video cable INPUT4To RS-232C terminal Connecting the Power CordControlling the Projector by a Computer Turning the Projector On/Off Turning the Projector onAdjusting the Screen Size About the Setup GuideAdjusting the Projected Image Adjusting the Focus Image ProjectionAdjust lever Make small adjustments Adjusting the HeightUse the rear adjustment foot to make the projector level Rear adjustment footAV Mute button Volume buttons Input buttons Switching the Input ModeAdjusting the Volume Correcting Trapezoidal Distortion Press g Keystone to enter Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Press g KeystoneResize Mode Press HresizeVideo Displaying and Setting the Break Timer Operating with the Remote ControlAuto Sync Auto Sync Adjustment Selecting the Picture ModeInput 1 Component/INPUT Component/INPUT 3/INPUT Menu ItemsInput 1 RGB/INPUT2 RGB Items you can set with Help menu Help menu nPress Q or O and select Picture to adjust Using the Menu ScreenMenu Selections Adjustments Press BmenuPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press hENTERPicture Adjustment Picture menu Example Picture screen menu for Input 1 RGB mode2Adjusting the Image Menu operation nYou can move the projected image vertically Button Adjusting the Projected Image SCR ADJ menuSet Auto Keystone on the SCR ADJ menu to On For Manual Keystone CorrectionAdjusting the Projected Image SCR ADJ menu Adjusting the Projector Function PRJ ADJ menu Adjusting the Projector Function PRJ ADJ menu This function changes the fan rotation speedATaking the Keylock off Enter the same keycode in Re- confirmLocking the Operation Buttons Troubleshooting with Help menu Utilizing Help menu functionsMaintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer Connecting Pin Assignments GNDRS-232C Specifications and Command Settings Return code 0DHCommands Control Contents Input 4 CLR Temp *2 OK or ERR Computer Compatibility Chart PC/MACTroubleshooting 23-26Input 1 Component For Sharp Assistance Specifications XG-MB65XDimensions Index