Sharp XG-MB65X operation manual Adjusting the Projector Function PRJ ADJ menu

Page 48

Adjusting the Projector Function (“PRJ - ADJ” menu) (Continued)

6Selecting the Transmission Speed (RS-232C)

Make sure that both the projector and computer are set for the same baud rate.

Selectable

Description

items

 

9600bps Transmission speed is slow.

P

R

115200bps Transmission speed is rapid.

7Fan Mode Setting

This function changes the fan rotation speed.

Selectable

Description

items

 

Normal

Suitable for normal environments.

 

 

High

Select this when using the projector at

 

altitudes of approximately 1,500

 

meters (4,900 feet) or more.

 

 

When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.

9Checking the Lamp Life Status

You can confirm the cumulative lamp usage time and the remaining lamp life (percentage).

Lamp usage condition

Remaining lamp life

 

 

 

 

 

“Life”

100%

5%

 

 

 

 

Operated exclusively

Approx.

Approx.

with Lamp Setting set to

3,000

150 hours

“Eco +Quiet”

hours

 

 

 

 

 

Operated exclusively

Approx.

Approx. 75

with Lamp Setting set to

1,500

hours

“Bright”

hours

 

 

 

 

 

Menu operation n Page 37

8System Lock Function

This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest you record the keycode in a safe place where only au- thorized users have access.

Info

If you lose or forget your keycode, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 61). Even if the prod- uct warranty is valid, the keycode reset will incur a charge.

aSetting/Changing the keycode

1Press the 4 buttons on the remote control or on the projector to en- ter the preset keycode in “Old Code”.

When setting the keycode for the first time, press R on the projector for four times.

 

 

PRJ - ADJ

 

 

 

Setting the System Lock

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Old Code

 

 

 

New Code

 

– – – –

 

 

Reconfirm

 

– – – –

 

Note

If you input a wrong keycode, the cursor returns to the first point of the “Old Code”.

The preset keycode is 4 R buttons on the projector. When you press the R but- ton four times, the keycord input screen disappears.

Note

It is recommended that the lamp be changed when the remaining lamp life becomes 5%.

The lamp life may vary depending on the us- age condition.

44

Image 48
Contents XG-MB65X This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianIii Page IntroductionENGLISH A. onlySharp PROJECTOR, Model XG-MB65X Sharp Electronics CorporationUsing the Menu Screen For Future ReferenceContents Reference Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Accessories Optional accessoriesHeight 29 Adjust Part Names and FunctionsProjector Rear View Audio Input 1Audio Input Break Timer Picture ModeInserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range Setup and Projection Quick StartHeight Upper side ProjectorSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode Example Normal Mode Picture SizeProjection DistanceNormal Mode Stretch ModeScreen Size and Projection Distance Connections Input Terminals and Connectable Main EquipmentCOMPUTER-RGB/COMPONENT Samples of Cables for Connection Connecting to a Computer To audio output terminal To RGB output terminalComputer To INPUT1 terminal To Audio Terminal Connecting to Video Equipment When using an S-video cable INPUT3Connecting to a Monitor with RGB Input Terminal When using a composite video cable INPUT4Connecting the Power Cord Controlling the Projector by a ComputerTo RS-232C terminal Turning the Projector On/Off Turning the Projector onAbout the Setup Guide Adjusting the Projected Image Adjusting the FocusAdjusting the Screen Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelAdjust lever Make small adjustments Rear adjustment footSwitching the Input Mode Adjusting the VolumeAV Mute button Volume buttons Input buttons Press g Keystone to enter Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Press g KeystoneResize Mode Press HresizeVideo Operating with the Remote Control Auto Sync Auto Sync AdjustmentDisplaying and Setting the Break Timer Selecting the Picture ModeMenu Items Input 1 RGB/INPUT2 RGBInput 1 Component/INPUT Component/INPUT 3/INPUT Items you can set with Help menu Help menu nUsing the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Press BmenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press hENTERPicture Adjustment Picture menu Example Picture screen menu for Input 1 RGB mode2Adjusting the Image Menu operation nAdjusting the Projected Image SCR ADJ menu Set Auto Keystone on the SCR ADJ menu to OnYou can move the projected image vertically Button For Manual Keystone CorrectionAdjusting the Projected Image SCR ADJ menu Adjusting the Projector Function PRJ ADJ menu Adjusting the Projector Function PRJ ADJ menu This function changes the fan rotation speedEnter the same keycode in Re- confirm Locking the Operation ButtonsATaking the Keylock off Troubleshooting with Help menu Utilizing Help menu functionsMaintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments GNDRS-232C Specifications and Command Settings Return code 0DHCommands Control Contents Input 4 CLR Temp *2 OK or ERR Computer Compatibility Chart PC/MACTroubleshooting 23-26Input 1 Component For Sharp Assistance Specifications XG-MB65XDimensions Index