Sharp XG-MB65X operation manual Specifications

Page 66

Specifications

Product type

Projector

 

Model

XG-MB65X

 

Video system

NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/

 

DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50

Display method

Single Chip Digital Micromirror DeviceTM (DMDTM) by Texas Instruments

DMD panel

Panel size: 0.55" (14 mm), 1chip XGA DMD

 

No. of dots: 786,432 dots (1,024 [H] × 768 [V])

Lens

1–1.15 × zoom lens, F2.4–2.6, f = 18.7–21.5 mm

Projection lamp

300 W DC lamp

 

Component input signal

15-pin mini D-sub connector

(INPUT1/2)

Y: 1.0 Vp-p, sync negative, 75 Ω terminated

 

PB: 0.7 Vp-p, 75 Ω terminated

 

PR: 0.7 Vp-p, 75 Ω terminated

Horizontal resolution

600 TV lines (DTV720P)

Computer RGB input

15-pin mini D-sub connector

(INPUT 1/2)/output

RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated

(OUTPUT) signal

HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)

 

VERTICAL SYNC. SIGNAL: Same as above

S-video input signal

4-pin mini DIN connector

(INPUT 3)

Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated

 

C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated

Video input signal

RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω

(INPUT 4)

terminated

 

Vertical frequency

45–85 Hz

 

Horizontal frequency

15–70 kHz

 

Pixel clock

12–108 MHz

 

RS-232C terminal

9-pin mini DIN connector

Audio input signal

ø3.5 mm minijack or RCA terminal: 0.5 Vrms, more than 22 kΩ (stereo)

Audio output signal

ø3.5 mm minijack: 0.5 Vrms, less than 2.2 kΩ

(AUDIO OUTPUT 1-4)

4 cm × 2.85 cm oval × 1

Speaker system

Rated voltage

AC 110–240 V

 

Input current

3.6 A

 

Rated frequency

50/60 Hz

 

Power consumption

385 W (Lamp Setting

“Bright”)/

 

308 W (Lamp Setting

“Eco + Quiet”) with AC 110 V

 

367 W (Lamp Setting

“Bright”)/

 

300 W (Lamp Setting

“Eco + Quiet”) with AC 240 V

Power consumption (standby) 4.7 W (AC 110 V) – 5.6 W (AC 240 V)

Heat dissipation

1,450 BTU/hour (Lamp Setting “Bright”)/

 

1,160 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 110 V

 

1,380 BTU/hour (Lamp Setting “Bright”)/

 

1,130 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 240 V

Operating temperature

41°F to 95°F (+5°C to +35°C)

Storage temperature

–4°F to 140°F (–20°C to +60°C)

Cabinet

Plastic

 

I/R carrier frequency

38 kHz

 

Dimensions (approx.)

12 13/32" × 4 19/64" × 11 1/32" (315 (W) × 109 (H) × 280 (D) mm) (main body only)

 

12 13/32" × 4 47/64" × 11 37/64" (315 (W) × 120 (H) × 294 (D) mm) (including adjust-

 

ment foot and projecting parts)

Weight (approx.)

8.6 lbs. (3.9 kg)

 

Replacement parts

Remote control, Power cord for U.S. and Canada, etc., Power cord for Europe,

 

except U.K., Power cord for U.K. and Singapore, Power cord for Australia, New

 

Zealand and Oceania, RGB cable, DIN-D-sub RS-232C adaptor, Operation

 

manual (Printed and CD-ROM)

As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specifica- tion figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

62

Image 66
Contents XG-MB65X This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianIii Page IntroductionENGLISH A. onlySharp PROJECTOR, Model XG-MB65X Sharp Electronics CorporationUsing the Menu Screen For Future ReferenceContents Reference Power Sources CleaningAccessories Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingRest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Accessories Optional accessoriesHeight 29 Adjust Part Names and FunctionsProjector Rear View Audio Input 1Audio Input Break Timer Picture ModeInserting the Batteries Attach the cover and slide it until it clicks into placeUsable Range Setup and Projection Quick StartHeight Upper side ProjectorStandard Setup Front Projection Setting up the ProjectorSetting up the Projector Ceiling-mount SetupProjection Projection PRJ ModeExample Normal Mode Picture Size DistanceNormal Mode Stretch ModeScreen Size and Projection Distance Connections Input Terminals and Connectable Main EquipmentCOMPUTER-RGB/COMPONENT Samples of Cables for Connection Connecting to a Computer To audio output terminal To RGB output terminalComputer To INPUT1 terminal To Audio Terminal Connecting to Video Equipment When using an S-video cable INPUT3Connecting to a Monitor with RGB Input Terminal When using a composite video cable INPUT4Connecting the Power Cord Controlling the Projector by a ComputerTo RS-232C terminal Turning the Projector On/Off Turning the Projector onAdjusting the Screen Size About the Setup GuideAdjusting the Projected Image Adjusting the Focus Image ProjectionAdjust lever Make small adjustments Adjusting the HeightUse the rear adjustment foot to make the projector level Rear adjustment footSwitching the Input Mode Adjusting the VolumeAV Mute button Volume buttons Input buttons Correcting Trapezoidal Distortion Press g Keystone to enter Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Press g KeystoneResize Mode Press HresizeVideo Displaying and Setting the Break Timer Operating with the Remote ControlAuto Sync Auto Sync Adjustment Selecting the Picture ModeMenu Items Input 1 RGB/INPUT2 RGBInput 1 Component/INPUT Component/INPUT 3/INPUT Items you can set with Help menu Help menu nPress Q or O and select Picture to adjust Using the Menu ScreenMenu Selections Adjustments Press BmenuPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press hENTERPicture Adjustment Picture menu Example Picture screen menu for Input 1 RGB mode2Adjusting the Image Menu operation nYou can move the projected image vertically Button Adjusting the Projected Image SCR ADJ menuSet Auto Keystone on the SCR ADJ menu to On For Manual Keystone CorrectionAdjusting the Projected Image SCR ADJ menu Adjusting the Projector Function PRJ ADJ menu Adjusting the Projector Function PRJ ADJ menu This function changes the fan rotation speedEnter the same keycode in Re- confirm Locking the Operation ButtonsATaking the Keylock off Troubleshooting with Help menu Utilizing Help menu functionsMaintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments GNDRS-232C Specifications and Command Settings Return code 0DHCommands Control Contents Input 4 CLR Temp *2 OK or ERR Computer Compatibility Chart PC/MACTroubleshooting 23-26Input 1 Component For Sharp Assistance Specifications XG-MB65XDimensions Index