Sharp XG-MB65X operation manual Turning the Projector On/Off, Turning the Projector on

Page 31

Turning the Projector On/Off

Turning the Projector on

Note that the connections to external equip- ment and power outlet should be done be- fore performing the operations written be- low. (See pages 23 to 26.)

Remove the lens cap and press SSTANDBY/ON on the projector or fON on the remote control.

•When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 44 for details.

Note

•About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on.

Blinking in green: The lamp is warming up or shut-

ting down.

Red: The lamp is shut down abnormally or the lamp should be replaced.

•When switching on the projector, a slight flickering of the image may be experienced within the first minute after the lamp has been illuminated. This is normal operation as the lamp’s control circuitry is stabilising the lamp output char- acteristics. It should not be regarded as faulty operation.

•If the projector is put into standby mode and immediately turned on again, the lamp may take some time to start pro- jection.

Turning the Power off (Putting the Projector into Standby Mode)

1	Press SSTANDBY/ON on the pro-
1	jector or eSTANDBY on the re-
	mote control, then press that but-
	ton again while the confirmation
	message is displayed, to put the
	projector into standby mode.
2	Unplug the power cord from the AC
2	outlet after the cooling fan stops.

• The power indicator on the projector blinks in green while cooling.

• The power indicator changes to red when the projector finishes cooling.

Info

•English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 42.

Lamp indicator

Power indicator

STANDBY/ON button

STANDBY button

ON button	Operation Basic
ON button
On-screen Display (confirmation message)

R

Info

•Do not unplug the power cord during projection or cooling fan operation. This can cause dam- age due to rise in internal temperature, as the cooling fan also stops.

27

Image 31

Contents XG-MB65X If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedIii Page A. only IntroductionENGLISHSharp Electronics Corporation Sharp PROJECTOR, Model XG-MB65XFor Future Reference Using the Menu ScreenContents Reference Power-Cord Protection CleaningAccessories Power SourcesOverloading Damage Requiring ServiceReplacement Parts Safety CheckAvoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the exhaust and intake vents Temperature monitor function Using the projector in other countriesOther connected equipment Optional accessories AccessoriesPart Names and Functions Height 29 AdjustProjector Audio Input 1 Rear ViewAudio Input Picture Mode Break TimerAttach the cover and slide it until it clicks into place Inserting the BatteriesUsable Range Quick Start Setup and ProjectionHeight Projector Upper sideCeiling-mount Setup Setting up the ProjectorSetting up the Projector Standard Setup Front ProjectionDistance Projection PRJ ModeExample Normal Mode Picture Size ProjectionStretch Mode Normal ModeScreen Size and Projection Distance Input Terminals and Connectable Main Equipment ConnectionsCOMPUTER-RGB/COMPONENT Samples of Cables for Connection To audio output terminal To RGB output terminal Connecting to a ComputerComputer To INPUT1 terminal To Audio Terminal When using an S-video cable INPUT3 Connecting to Video EquipmentWhen using a composite video cable INPUT4 Connecting to a Monitor with RGB Input TerminalControlling the Projector by a Computer Connecting the Power CordTo RS-232C terminal Turning the Projector on Turning the Projector On/OffImage Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Adjusting the Screen SizeRear adjustment foot Adjusting the HeightUse the rear adjustment foot to make the projector level Adjust lever Make small adjustmentsAdjusting the Volume Switching the Input ModeAV Mute button Volume buttons Input buttons Press g Keystone Press g Keystone to enter Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionPress Hresize Resize ModeVideo Selecting the Picture Mode Operating with the Remote ControlAuto Sync Auto Sync Adjustment Displaying and Setting the Break TimerInput 1 RGB/INPUT2 RGB Menu ItemsInput 1 Component/INPUT Component/INPUT 3/INPUT Help menu n Items you can set with Help menuPress Bmenu Using the Menu ScreenMenu Selections Adjustments Press Q or O and select Picture to adjustPress hENTER To adjust the projected image while watching itPress P or R and select Bright to adjust Press O or Q to adjust the item selectedExample Picture screen menu for Input 1 RGB mode Picture Adjustment Picture menuMenu operation n 2Adjusting the ImageFor Manual Keystone Correction Adjusting the Projected Image SCR ADJ menuSet Auto Keystone on the SCR ADJ menu to On You can move the projected image vertically ButtonAdjusting the Projected Image SCR ADJ menu Adjusting the Projector Function PRJ ADJ menu This function changes the fan rotation speed Adjusting the Projector Function PRJ ADJ menuLocking the Operation Buttons Enter the same keycode in Re- confirmATaking the Keylock off Utilizing Help menu functions Troubleshooting with Help menuCleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Lamp Regarding the LampReplacing the Lamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer GND Connecting Pin AssignmentsReturn code 0DH RS-232C Specifications and Command SettingsCommands Control Contents Input 4 CLR Temp *2 OK or ERR PC/MAC Computer Compatibility Chart23-26 TroubleshootingInput 1 Component For Sharp Assistance XG-MB65X SpecificationsDimensions Index