Sharp XG-C60X operation manual Connecting the thumbscrew cables, Ferrite core

Page 22

Connecting the Projector to Other Devices

Connecting the thumbscrew cables

■ Connect the thumbscrew cable making sure that it fits correctly into the terminal. Then, firmly se- cure the connectors by tightening the screws on both sides of the plug.

■ Do not remove the ferrite core attached to the RGB cable.

Ferrite core

“Plug and Play” function (when connecting to a 15-pin terminal)

■This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible computer will communicate their setting requirements, allowing for quick and easy setup.

■Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.

Note

•The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA DDC compatible computer.

-18

XG-C60X_E_PDF_p15_18.p65

03.8.28, 1:56 PM

Image 22

Contents XG-C60X Model No. XG-C60X Serial No Special Note for Users in the U.K 03.8.28, 155 PM Introduction When Attaching the Quick Guide Label Product DisposalNoise Reduction Outstanding FeaturesColor Management System New Edge Up-ScalingContents Appendix Power Sources CleaningAccessories Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts Wall or Ceiling MountingTemperature monitor function Avoid locations with high or low temperatureUsing the projector in other countries Rest your eyes occasionallyFor Windows To install Acrobat Reader from the CD-ROMFor other operating systems For other languages For MacintoshPart Names Projector Front and Top ViewUsing the Kensington Lock Projector Rear ViewRemote Control Top View Remote Control Front ViewPart Names When using the remote control Using the Remote ControlAvailable Range of the Remote Control Inserting the BatteriesSupplied accessories AccessoriesOptional cable Connections and Setup This projector can be connected to Connecting the Projector to Other DevicesBefore Connecting An audio cable commercially available SeeConnecting the Power Cord Connecting to a Computer Using the RGB CableConnecting the thumbscrew cables Ferrite coreConnecting to Video Equipment Connecting to Component Video Equipment Connecting to an Amplifier Connecting to an Amplifier or Other Audio ComponentsControlling the Projector by a Computer Connecting the Remote Control to the Projector Watching Images on Both the Projector and a MonitorPress or while using presentation software on your computer Using the Wireless Pre- sentation FunctionButton Setup Using the Adjustment FeetFocus ring Zoom knob Adjusting the LensOut Zoom Setting up the Screen Throw DistanceStretch Mode Normal ModeScreen Size and Projection Distance AN-C41MZ Optional accessory Throw ratio 14.1 to AN-C27MZ Optional accessory Throw ratio 12.7 to AN-C12MZ Optional accessory Throw ratio 11.18 to Projecting a Reversed/Inverted Image Projection from behind the screenBasic Operation Press on the projector or on the remote control Basic ProcedurePlug the power cord into the wall outlet Image ProjectionPress or on the remote control to adjust the volume Press , , or on the remote control to select the Input modeInput buttons Volume buttons Press to temporarily turn off the sound Selecting the On-screen Display LanguagePress Menu button Buttons Mute button Turning the Power offPress Standby on the projector Standby button Enter buttonCorrecting Trapezoidal Distortion Press , , \ and to adjust the Keystone correctionCorrecting Trapezoidal Distortion Keystone Correction Keystone button Enter button Undo button ButtonsDigital Shift Setting Menu Bar Items Sub menuInput 3 / 4 Mode Main menu Sub menuMenu Selections Adjustments Using the Menu ScreenMenu Bar Main Menu Enter button Buttons Menu button Press or to select the item you want to adjust Press \ or to select the menu you want to adjustPress \or to adjust the item selected Press or to select the item you want to set Menu Selections SettingsEnter button Buttons Menu button Cursor shifts to the sub menu Adjusting Image Preferences Adjusting the PictureSelecting the Signal Type Progressive Mode Computer Image Adjustment Adjusting Computer ImagesSaving Adjustment Settings Special Mode Settings Selecting Adjustment SettingsChecking the Input Signal Manual adjustments should be per- formed Auto Sync AdjustmentWhen setting to Normal or High Speed Auto Sync Display FunctionEasy to Use Functions Switching the Picture Display Using Different Input Signals Selecting the Picture Display ModeResize button Screen display of the picture display mode Video Freezing a Moving Image Displaying a Still ImageFreeze button Displaying an Enlarged Portion of an Image Enlarging a Specific Portion of an ImageButtons Enlarge Enlarge/ Reduce buttons Adjusting Gamma Correction Gamma Correction FunctionDisplaying the Inset Picture Displaying Dual Pictures Pict in PictPress to move the inset pic- ture To return to the original projected image, press again Black Screen FunctionBlacking out the Pro- jected Image This function can be used to display a black screenPress to cancel the break timer Displaying the Break TimerDisplaying and Setting the Break Timer Buttons Break Timer buttonSelecting the Color Reproduction Mode Selecting the Target ColorSetting the Chromatic Value of the Target Color Setting the Brightness of the Target ColorSetting the Hue of the Target Color Resetting User-Defined Color Settings Overview of All Color SettingsSetting the Audio Out- put Type Setting the Audio Output TypeSetting on/off the Internal Speaker Setting on/off the Inter- nal SpeakerUsing Auto Search Auto Search FunctionReducing Image Noise Setting On-screen DisplayVideo Digital Noise Reduction DNR System Turning Off On-screen DisplaySetting the Video System Setting the Video SystemCapturing the Image Saving Projected ImagesDeleting the Captured Image Selecting a Background Image Setting a Background ImageSelecting a Startup Image Selecting a Startup ImageSetting the Power Save Mode Selecting the Economy ModeMonitor Out/RS-232C Off Function Displaying the Remaining Lamp Life Percentage Auto Power Off FunctionSelecting the Economy Mode Checking the Remaining Lamp Life PercentageReversing/Inverting Projected Images Setting the Projection ModeSetting up the Keylock Locking the Operation Buttons on the ProjectorSelecting the Transmission Speed RS-232C Canceling the Keylock SettingSelecting the Transmis- sion Speed RS-232C Setting up a Password Entering the PasswordChanging the Password If You Forget Your PasswordSetting the Anti-Theft Entering the KeycodeChanging the Keycode Enter the same 4-digit keycode in ReconfirmInitializing the Settings Returning to Default SettingsDisplaying the Adjustment Settings Overview of All Menu SettingsAppendix Cleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsReplacing the Air Filter Cleaning and replacing the bottom air filterDisconnect the power cord Remove the bottom filter coverReplace the air filter Clean the air filterReplace the filter cover About the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator Maintenance Indicators Lamp Regarding the LampReplacing the Lamp Change the air filter Removing and Install- ing the Lamp UnitAC socket User service screw Remove the lamp unit coverResetting the Lamp Timer Connecting Pin Assignments RGB Input Component InputPC control RS-232C Specifications and Command SettingsCommands Communication conditionsRS-232C Specifications and Command Settings Options Control Contents Sharp remote control signal format Wired Remote Control Terminal SpecificationsSpecifications of wired remote control input Function and transmission codesComputer Compatibility Chart VGATroubleshooting Sxga For Sharp Assistance Specifications Ntsc 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAMDimensions Units inches mmGlossary Advanced intelligent compressionIndex 100101 Sharp Corporation